User manual SAMSUNG SYNCMASTER 171MP

[. . . ] SyncMaster 151MP / 171MP English > Main > Index Main Page Safety Instructions Notational Power Installation Cleaning Other Introduction Unpacking Front Rear Remote Control Setup Connecting Your Monitor Connecting to a Computer Connecting to Other Devices Installing the Monitor Driver Automatic Manual Installing a VESA Base Folding or removing the base Installing a VESA Base Adjusting Your LCD Monitor User Controls User control buttons Direct-Access Features On-Screen Display OSD Functions Screen Adjustment Animation Clips Troubleshooting Check before Calling for Service Problems and Solutions Q&A Specifications General Specifications PowerSaver Preset Timing Modes Information Service Center Terms Regulatory Natural Color Authority English > Main > Safety Instructions > Notational Notational Power Installation Cleaning Other Failure to follow directions noted by this symbol could result in bodily harm or damage to equipment. Prohibited Important to read and understand at all times Do not disassemble Disconnect the plug from the outlet Do not touch Grounding to prevent an electric shock English > Main > Safety Instructions > Power When not used for extended periods of time, set your PC to DPMS. If using a screen saver, set it to the active screen mode. Notational Power Installation Cleaning Other This may cause an electric shock or fire. Do not use a damaged or loose plug. Do not pull the plug out by the wire nor touch the plug with wet hands. [. . . ] Sometimes the screen turns black without the "Video mode not supported" message appearing on the screen. This indicates the monitor is set for a frequency out of range or the PowerSaver mode is on. 3. Display Adapter Driver Display adapter refers to the computer video card driver. If the adapter is not properly set, you cannot adjust resolution, frequency or color and you cannot install the monitor driver. 1. Checking Adapter Driver Click Start --> Settings --> Control Panel --> Display --> Settings --> Advanced --> Adapter. If "Default" or a wrong product model is indicated, it means that the adapter driver is not properly installed. Install the adapter driver again according to the information provided by the computer or video card manufacturers. Installing Adapter Driver The instructions given below are for general circumstances. For specific issues, contact the relevant computer or video card manufacturers. 1) Click Start --> Settings --> Control Panel --> Display --> Settings --> Advanced --> Adapter --> Update Driver --> Next --> Display a list of the known drivers for this device so that I can choose a specific driver --> Next -> Have Disk (Insert Video Card Driver diskette) -> OK -> Next -> Next -> Finish. 2) In case you have Adapter Driver Setup file on your computer: Run Setup. exe or Install. exe, which is found in the Adapter Driver Setup file. 4. Selecting Resolution and Color If the monitor resolution or color is not properly set, the screen may show blurred images or mosaic patterns. Procedures for setting frequency in the Control Panel may vary depending on the video card. Setting Color & Resolution >> Click Start --> Settings --> Control Panel --> Display --> Settings --> Colors & Screen area --> Apply --> OK. You can get the best image quality by selecting resolution depending on the monitor screen size as follows: · 15 inch monitor : 1024 x 768 @60Hz · 17 inch monitor : 1280 x 1024 @60Hz Select 16 or 24 bit color. · Supported or not subject to the video card (the monitor is irrelevant) · LCD monitors may display up to 16. 77 million colors (24 bits). Setting Refresh Rate If the monitor refresh rate is not properly set, the screen image may be skewed or noise patterns will appear. You can enjoy the best screen image when the refresh rate is set to 60 Hz. Setting Refresh Rate >> Click Start --> Settings --> Control Panel --> Display --> Settings --> Advanced --> Refresh Rate --> Apply -> Yes --> OK --> Yes. Activate the AUTO ADJUSTMENT feature for better picture quality. If the noise persists even after AUTO ADJUSTMENT, adjust the screen settings using FINE/COARSE tuning buttons. 5. Dot Acceptable TFT LCD panel manufactured by using advanced semiconductor technology with precision of 99. 999% above is used for this product. [. . . ] Important parameters are luminance, contrast, resolution, reflectance, colour rendition and image stability. Energy Energy-saving mode after a certain time - beneficial both for the user and the environment Electrical safety Emissions Electromagnetic fields Noise emissions Ecology The product must be prepared for recycling and the manufacturer must have a certified environmental management system such as EMAS or ISO 14 000 Restrictions on o chlorinated and brominated flame retardants and polymers o heavy metals such as cadmium, mercury and lead. The requirements included in this label have been developed by TCO Development in cooperation with scientists, experts, users as well as manufacturers all over the world. Since the end of the 1980s TCO has been involved in influencing the development of IT equipment in a more user-friendly direction. [. . . ]