User manual SAMSUNG 171N

[. . . ] SyncMaster 181T/191T/171T/171S/171V/191N/170N/172N/192N/173N/193N Notational Power Installation Clean Other Failure to follow directions noted by this symbol could result in bodily harm or damage to equipment. Prohibited Important to read and understand at all times Do not disassemble Disconnect the plug from the outlet Do not touch Grounding to prevent an electric shock Notational When not used for extended periods of time, set your PC to DPMS. If using a screen saver, set it to the active screen mode. Power Installation Clean Other Do not use a damaged or loose plug. This may cause an electric shock or fire. Do not pull the plug out by the wire nor touch the plug with wet hands. This may cause an electric shock or fire. Use only a properly grounded plug and recepticle. [. . . ] Unplug the video cable from the back of the computer. If the monitor is functioning properly, you will see a box with a border and text inside as shown in the following illustration: The three boxes inside the border are red, green and blue. Failure of any of the boxes to appear indicates a problem with your monitor. This box also appears during normal operation if the video cable becomes disconnected or damaged. Turn off your monitor and reconnect the video cable; then turn on both your computer and the monitor. If your monitor screen remains blank after using the previous procedure, check your video controller and computer system; your monitor is functioning properly. If there is something wrong with the input signal, a message appears on the screen or the screen goes blank although the power indicator LED is still on. The message may indicate that the monitor is out of scan range or that you need to check the signal cable. If the vertical frequency is set at over 76HZ, this message will appear for 5 seconds and then disappear. The location and the position of the monitor may influence the quality and other features of the monitor. If there are any woofer speakers near the monitor, unplug and relocate the woofer to another room. Remove all electronic devices such as radios, fans, clocks and telephones that are within 3 feet (one meter) of the monitor. A monitor recreates visual signals received from the PC. Therefore, if there is trouble with the PC or the video card, this can cause the monitor to become blank, have poor coloring, noise, Video mode not supported, etc. In this case, first check the source of the problem, and then contact a service center or your dealer. Judging the monitor's working condition If there is no image on the screen or an "Video mode not supported" message comes up, disconnect the cable from the computer while the monitor is still powered on. If there is a message coming up on the screen or if the screen goes white, this means the monitor is in working condition. In this case, check the computer for trouble. SyncMaster 181T General Model Name LCD Panel Size General PowerSaver Preset Timing Modes SyncMaster 181T 18. 1 inch diagonal 359. 04 (H) x 287. 232 (V) 0. 2805 (H) x 0. 2805 (V) a-si TFT active matrix 80/80/80/80(L/R/T/B), Typical Display area Pixel Pitch Type Viewing Angle Synchronization Horizontal Vertical Display Color 16. 294. 277 Colors Resolution Optimum resolution Maximum resolution Input Signal, Terminated 30 ~ 81 kHz 56 ~ 85 Hz 1280 x 1024@60Hz 1280 x 1024@76Hz RGB Analog 0. 7 Vpp, Digital TMDSTM positive at 75 ohms Separate H/V sync, Composite, Sync-On-Green TTL level positive or negative Maximum Pixel Clock 135 MHz Power Supply AC 90 ~ 264 VAC, 60/50 Hz ± 3Hz Signal Cable 15pin-to-15pin D-sub cable, detachable DVI-D to DVI-D cable, detachable Power Consumption 40W (Maximum) Dimensions (WxDxH) / Weight 398. 2 X 208. 4 X 443. 2 mm / 5. 8kg(With Simple Stand) VESA Mounting Interface 100mm x 100mm (for use with Specialty(Arm) Mounting hardware. ) Environmental considerations Operating Storage Dot Acceptable TFT LCD panel manufactured by using advanced semiconductor technology with precision of 99. 999% above is used for this product. But the pixels of RED, GREEN, BLUE and WHITE color seem to be bright sometimes or some of black pixels could be seen. This is not from bad quality and you can use it without uneasiness. of TFT LCD pixels that is contained in this product are 3, 932, 160. Plug and Play Capability This monitor can be installed on any Plug & Play compatible system. Interaction of the monitor and computer systems will provide the best operating conditions and monitor settings. In most cases, monitor installation will proceed automatically, unless the user wishes to select alternate settings. Note: Design and specifications are subject to change without prior notice. Temperature: 50°F ~ 104°F(10°C ~ 40°C) Humidity: 10% ~ 80%, non-condensing Temperature: -4°F ~113°F (-20°C ~ 45°C) Humidity: 5% ~ 95%, non-condensing SyncMaster 191T General Model Name LCD Panel Size General PowerSaver Preset Timing Modes SyncMaster 191T 19. 0 inch diagonal 376. 32 (H) x 301. 056 (V) 0. 298 (H) x 0. 294 (V) a-si TFT active matrix 85/85/85/85(L/R/T/B) Display area Pixel Pitch Type Viewing Angle Synchronization Horizontal Vertical Display Color 16. 294. 277 Colors Resolution Optimum resolution Maximum resolution Input Signal, Terminated 30 ~ 81 kHz 56 ~ 85 Hz 1280 x 1024@60Hz 1280 x 1024@75Hz RGB Analog 0. 7 Vp-p positive at 75 ohms Separate H/V sync, Composite, SOG TTL level positive or negative Maximum Pixel Clock 135 MHz Power Supply AC 90 ~ 264 VAC rms, 60/50 Hz ± 3Hz Signal Cable 15pin-to-15pin D-sub cable, detachable DVI-D to DVI-D cable, detachable Power Consumption 40W (Maximum) Dimensions (WxDxH) / Weight 416. 3 X 190. 3 X 408. 5 mm / 5. 6kg (With Simple Stand) VESA Mounting Interface 100mm x 100mm (for use with Specialty(Arm) Mounting hardware. ) Environmental considerations Operating Storage Dot Acceptable TFT LCD panel manufactured by using advanced semiconductor technology with precision of 99. 999% above is used for this product. [. . . ] To install the program manually, insert the CD included with the Samsung monitor into the CD-ROM Drive, click the [Start] button of Windows and then select [Execute]. Enter D:\color\eng\setup. exe and then press the <Entrer> key. (If the drive where the CD is inserted is not D:\, enter the applicable drive. ) How to delete the Natural Color software program Select [Setting]/[Control Panel] on the [Start] menu and then double-click [Add/Delete a program]. Select Natural Color from the list and then click the [Add/Delete] button. For Better Display 1. [. . . ]