User manual SAMSUNG SYNCMASTER 192T MM

[. . . ] SyncMaster 192B/192T User's Manual Index Main Page On-Screen Display Safety Instructions Notational Power Installation Cleaning Other Troubleshooting Check List Q&A Self-Test Feature Check Introduction Unpacking Front Rear Specifications General Specifications PowerSaver Preset Display Modes Setup Connecting Your Monitor Installing the Monitor Driver -- Automatic -- Manual Information Service Terms Regulatory Natural Color For Better Display Authority User's Manual Safety Instructions Notational Warning/Caution Failure to follow directions noted by this symbol could result in bodily harm or damage to equipment. Notation Conventions Prohibited Important to read and understand at all times Do not disassemble Disconnect the plug from the outlet Do not touch Grounding to prevent an electric shock User's Manual Safety Instructions Power When not used for extended periods of time, set your PC to DPMS. If using a screen saver, set it to the active screen mode. · Do not use a damaged or loose plug. · This may cause an electric shock or fire. · Do not pull the plug out by the wire nor touch the plug with wet hands. · This may cause an electric shock or fire. · Use only a properly grounded plug and recepticle. · An improper ground may cause electric shock or equipment damage · Do not excessively bend the plug and wire nor place heavy objects upon them, which could cause damage. · Failure to do so may cause an electric shock or fire. User's Manual Safety Instructions Power · Disconnect the plug from the outlet during storms or lightening or if it is not used for a long period of time. · Failure to do so may cause an electric shock or fire. · Do not connect too many extension cords or plugs to an outlet. · This may cause a fire. User's Manual Safety Instructions Installation · Do not cover the vents on the monitor cabinet. · Bad ventilation may cause a breakdown or fire. · Put your monitor in a location with low humidity and a minimum of dust. · An electric shock or fire could result inside the monitor. · Do not drop the monitor when moving it. · This may cause damage to the product or human body. · Place the monitor on a flat and stable surface. · The monitor can cause injury by falling. · Set down the monitor carefully. · It could be damaged or broken. User's Manual Safety Instructions Installation · Do not place the monitor face down. · The TFT-LCD surface may be damaged. User's Manual Safety Instructions Clean When cleaning the monitor case or the surface of the TFT-LCD, wipe with a slightly moistened, soft fabric. · Do not spray detergent directly on the monitor. · Use the recommended detergent with a smooth cloth. · If the connector between the plug and the pin is dusty or dirty, clean it properly with a dry cloth. · A dirty connector can cause an electric shock or fire · Do not set a glass of water, chemicals or any small metal objects on the monitor. · · This may cause damage, electric shock or a fire. If a foreign substance gets into the monitor, disconnect the plug and then contact a service center. User's Manual Safety Instructions Other · Do not remove cover(or back). No user serviceable parts inside. · · This may cause an electric shock or a fire. [. . . ] Remove all electronic devices such as radios, fans, clocks and telephones that are within 3 feet (one meter) of the monitor. Useful Tips . A monitor recreates visual signals received from the PC. Therefore, if there is trouble with the PC or the video card, this can cause the monitor to become blank, have poor coloring, noise, Video mode not supported, etc. In this case, first check the source of the problem, and then contact a service center or your dealer. Judging the monitor's working condition If there is no image on the screen or an "Video mode not supported" message comes up, disconnect the cable from the computer while the monitor is still powered on. If there is a message coming up on the screen or if the screen goes white, this means the monitor is in working condition. In this case, check the computer for trouble. . User's Manual Specifications General (SyncMaster 192B) General Model Name LCD Panel Size Display area Pixel Pitch Type Viewing Angle Synchronization Horizontal Vertical Display Color 16, 294, 277 Colors Resolution Optimum resolution Maximum resolution Input Signal, Terminated RGB Analog, DVI Compliant Digital RGB. Composite Sync, SOG(cable option), 0. 7Vp-p Positive at 75 ohms , Separate H/V sync, TTL level positive or negative Maximum Pixel Clock 140 MHz Power Supply AC 90 ~ 264 VAC, 60/50 Hz ± 3Hz Signal Cable 15pin-to-15pin D-sub cable, detachable Power Consumption 45w (Maximum) Dimensions (WxDxH) / Weight 431 x 220 x 447 mm (After installing of Stand) 431 x 29. 7 x 324. 7 mm (After folding the stand) Weight 5. 5 kg (With Basic Stand) 5. 6 kg (Multimedia Stand) VESA Mounting Interface 75 mm x 75 mm (for use with Specialty(Arm) Mounting hardware. ) 1280 x 1024@60Hz 1280 x 1024@75Hz 30 ~ 81 kHz 56 ~ 75 Hz 19" Diagonal 376. 32 (H) x 301. 056 (V) 0. 297mm (H) x 0. 297mm (V) a-si TFT active matrix 170/170(L, R/T, B) SyncMaster 192B User's Manual Specifications General (SyncMaster 192B) Environmental considerations Operating Storage Plug and Play Capability This monitor can be installed on any Plug & Play compatible system. Interaction of the monitor and computer systems will provide the best operating conditions and monitor settings. In most cases, monitor installation will proceed automatically, unless the user wishes to select alternate settings. Dot Acceptable TFT LCD panel manufactured by using advanced semiconductor technology with precision of 99. 999% above is used for this product. But the pixels of RED, GREEN, BLUE and WHITE color seem to be bright sometimes or some of black pixels could be seen. This is not from bad quality and you can use it without uneasiness. For example, the number of TFT LCD pixels that is contained in this product are 3, 932, 160. Note: Design and specifications are subject to change without prior notice. Temperature: 50°F ~ 104°F(10°C ~ 40°C) Humidity: 10% ~ 80%, non-condensing Temperature: -4°F ~ 113°F (-20°C ~ 45°C) Humidity: 5% ~ 95%, non-condensing User's Manual Specifications General (SyncMaster 192T) General Model Name LCD Panel Size Display area Pixel Pitch Type Viewing Angle Synchronization Horizontal Vertical Display Color 16, 294, 277 Colors Resolution Optimum resolution Maximum resolution Input Signal, Terminated RGB Analog, DVI Compliant Digital RGB. Composite Sync, SOG(cable option), 0. 7Vp-p Positive at 75 ohms Separate H/V sync, TTL level positive or negative Maximum Pixel Clock 140 MHz Power Supply AC 90 ~ 264 VAC, 60/50 Hz ± 3Hz Signal Cable 15pin-to-15pin D-sub cable, detachable DVI-D to DVI-D cable, Detachable Power Consumption 45w (Maximum) Dimensions (WxDxH) 431 x 220 x 447 mm (After installing of Stand) 431 x 29. 7 x 324. 7 mm (After folding the stand) Weight 5. 5 kg (With Basic Stand) 5. 6 kg (Multimedia Stand) VESA Mounting Interface 75 mm x 75 mm (for use with Specialty(Arm) Mounting hardware. ) 1280 x 1024@60Hz 1280 x 1024@75Hz 30 ~ 81 kHz 56 ~ 75 Hz 19" Diagonal 376. 32 (H) x 301. 056 (V) 0. 297mm (H) x 0. 297mm (V) a-si TFT active matrix 170/170(L, R/T, B) SyncMaster 192T User's Manual Specifications General (SyncMaster 192T) Environmental considerations Operating Storage Plug and Play Capability This monitor can be installed on any Plug & Play compatible system. Interaction of the monitor and computer systems will provide the best operating conditions and monitor settings. In most cases, monitor installation will proceed automatically, unless the user wishes to select alternate settings. Dot Acceptable TFT LCD panel manufactured by using advanced semiconductor technology with precision of 99. 999% above is used for this product. But the pixels of RED, GREEN, BLUE and WHITE color seem to be bright sometimes or some of black pixels could be seen. This is not from bad quality and you can use it without uneasiness. For example, the number of TFT LCD pixels that is contained in this product are 3, 932, 160. [. . . ] Then, the initial screen of the program installation will be executed. Click Natural Color on the initial screen to install the Natural Color software. To install the program manually, insert the CD included with the Samsung monitor into the CD-ROM Drive, click the [Start] button of Windows and then select [Execute]. Enter D:\color\eng\setup. exe and then press the key. [. . . ]