User manual SAMSUNG SYNCMASTER 194T

[. . . ] SyncMaster 194T Main Page Safety Instructions Notational Power Installation Cleaning Other Introduction Unpacking Front Rear Setup Connecting the Monitor Installing the Monitor Driver Automatic Manual Installing VESA compliant mounting On-Screen Display Troubleshooting Check List Q&A Self-Test Feature Check Specifications General Specifications PowerSaver Preset Timing Modes Information Service Terms Regulatory Natural Color For Better Display Image Retention Free Authority Notational Power Installation Clean Other Failure to follow directions noted by this symbol could result in bodily harm or damage to equipment. Prohibited Important to read and understand at all times Do not disassemble Disconnect the plug from the outlet Do not touch Grounding to prevent an electric shock When not used for an extended period of time, set your computer to DPMS. If using a screen saver, set it to the active screen mode. Notational Power Installation Clean Other Do not use a damaged or loose plug. This may cause an electric shock or fire. Do not pull the plug out by the wire nor touch the plug with wet hands. This may cause an electric shock or fire. Use only a properly grounded plug and receptacle. [. . . ] The message may indicate that the monitor is out of scan range or that you need to check the signal cable. The location and the position of the monitor may influence the quality and other features of the monitor. If there are any sub woofer speakers near the monitor, unplug and relocate the woofer to another room. Remove all electronic devices such as radios, fans, clocks and telephones that are within 3 feet (one meter) of the monitor. A monitor recreates visual signals received from the computer. Therefore, if there is trouble with the computer or the video card, this can cause the monitor to become blank, have poor coloring, noise, Video mode not supported, etc. In this case, first check the source of the problem, and then contact a service center or your dealer. Judging the monitor's working condition If there is no image on the screen or a "Not Optimum Mode" message comes up, disconnect the cable from the computer while the monitor is still powered on. If there is a message coming up on the screen or if the screen goes white, this means the monitor is in working condition. In this case, check the computer for trouble. General Model Name General PowerSaver Preset Timing Modes SyncMaster 194T LCD Panel Size Display area Pixel Pitch Type Synchronization Horizontal Vertical Display Color 16. 7 Million Resolution Optimum resolution Maximum resolution Input Signal, Terminated RGB Analog , DVI(Digital Visual Interface) Compliant Digital RGB. 0. 7Vp-p ±5%, Positive bright, 75 ohms ±10%(terminated), Separate H/V sync, Composite, SOG, TTL level, positive or negative Maximum Pixel Clock 140 MHz Power Supply AC 100 ~ 240 VAC(+/- 10%) rms, 60/50 Hz ± 3Hz Signal Cable DVI-A to 15pin D-SUB cable, detachable DVI-D to DVI-D cable, detachable Power Consumption Less than 38W Dimensions (WxDxH) / Weight 416. 3 x 207. 0 x 411. 7 mm / 6. 3kg 416. 3 x 57. 9 x 342. 0 mm(Without Stand) VESA Mounting Interface 100mm x 100mm (for use with Specialty(Arm) Mounting hardware. ) Environmental considerations Operating Storage Plug and Play Capability This monitor can be installed on any Plug & Play compatible system. Interaction of the monitor and computer systems will provide the best operating conditions and monitor settings. In most cases, monitor installation will proceed automatically, unless the user wishes to select alternate settings. Dot Acceptable Temperature: 50°F ~ 104°F(10°C ~ 40°C) Humidity: 10% ~ 80%, non-condensing Temperature: -4°F ~113°F (-20°C ~ 45°C) Humidity: 5% ~ 95%, non-condensing 1280 x 1024@60Hz 1280 x 1024@75Hz 30 ~ 81 kHz 56 ~ 76 Hz 19. 0 inch diagonal 376. 32 (H) x 301. 056 (V) 0. 294 (H) x 0. 294 (V) a-si TFT active matrix TFT LCD panel manufactured by using advanced semiconductor technology with precision of 1ppm (one millionth) above is used for this product. But the pixels of RED, GREEN, BLUE and WHITE color seem to be bright sometimes or some of black pixels could be seen. This is not from bad quality and you can use it without uneasiness. For example, the no of TFT LCD sub pixels that is contained in this product are 3, 932, 160. Note: Design and specifications are subject to change without prior notice. General PowerSaver Preset Timing Modes This monitor has a built-in power management system called PowerSaver. This system saves energy by switching your monitor into a low-power mode when it has not been used for a certain amount of time. The monitor automatically returns to normal operation when you press a key on the keyboard. For energy conservation, turn your monitor OFF when it is not needed, or when leaving it unattended for long periods. The PowerSaver system operates with a VESA DPMS compliant video card installed in your computer. Use a software utility installed on your computer to set up this feature. State Power Indicator Power Consumption Normal Operation Green Less than 38W Power saving mode EPA/ENERGY 2000 Green, Blinking Less than 2W (When 'Manual' is selected in 'Auto source'. ) Mechanical Power S/W off(120Vac) Black 0W This monitor is EPA ENERGY STAR® compliant and ENERGY2000 compliant when used with a computer equipped with VESA DPMS functionality. [. . . ] All display products, including LCD, are subject to image retention. Please follow the suggestions below to protect your LCD from image retention Power Off, Screen Saver, or Power Save Mode Ex) Turn the power off when using a stationary pattern. - Turn the power off for 4 hours after 24 hours in use - Turn the power off for 2 hours after 12 hours in use Use a Screen saver if possible - Screen saver in one color or a moving image is recommended. Set the Monitor to power off with the PC Display Properties Power Scheme. [. . . ]