User manual SAMSUNG SYNCMASTER S19B420BW

[. . . ] 5) Sport For watching motion pictures such as a sport. 6) Movie For watching motion pictures such as a DVD or Video CD. 7) Dynamic Contrast Dynamic Contrast is to automatically detect distribution of inputted visual signal and adjust to create optimum contrast. >> Click here to see an animation clip Brightness button [ ] When OSD is not on the screen, push the button to adjust brightness. [. . . ] I cannot turn on the monitor. Check List Is the power cord connected properly?Can you see "Check Signal Cable" on the screen? Solutions Check the power cord connection and supply. (Connected using the D-sub cable) Check the signal cable connection. (Connected using the DVI cable) If you still see an error message on the screen when the monitor is connected properly, check to see if the monitor status is set to analog. Press SOURCE/ button to have the monitor doublecheck the input signal source. If the initial screen (the login screen) appears, boot the computer in the applicable mode (the safe mode for Windows ME/XP/2000) and then change the frequency of the video card. (Refer to the Preset Timing Modes) If the initial screen (the login screen) does not appear, contact the Service Center or your dealer. If the power is on, reboot the computer to see the initial screen(the login screen), which can be seen. Can you see "Not Optimum Mode", "Recommended Mode 1680 X 1050 60 Hz" on the screen? You can see this message when the signal from the video card exceeds the maximum resolution and frequency that the monitor can handle properly. Adjust the maximum resolution and frequency that the monitor can handle properly. If the display exceeds SXGA or 75 Hz, a "Not Optimum Mode", "Recommended Mode 1680 X 1050 60 Hz" message is displayed. If the display exceeds 85 Hz, the display will work properly but the "Not Optimum Mode", "Recommended Mode 1680 X 1050 60 Hz" message appears for one minute and then disappears. Please change to the recommended mode during this one-minute period. (The message is displayed again if the system is rebooted. ) There is no image on the screen. (The maximum frequency per resolution may differ from product to product. ) There are only 16 colors shown on the screen. The screen colors have changed after changing the video card. Windows XP : Set the resolution in the Control Panel Appearance and Themes Display Settings. Windows ME/2000 : Set the resolution in the Control Panel Display Settings. Has the video card been set properly?There is a message that Have you installed the monitor driver? Set the video card by referring to the video card manual. Install the monitor driver according to the Driver Installation Instructions. reads "Unrecognized monitor, Plug & Play (VESA DDC) monitor found". Check when MagicTuneTM does not function properly. See the video card manual to see if the Plug & Play (VESA DDC) function can be supported. MagicTuneTM feature is found only on PC (VGA) with Window OS that supports Plug and Play. Install the monitor driver according to the Driver Installation Instructions. * To check whether your PC is available for MagicTuneTM feature, follow the steps below (When Windows is XP); Control Panel Performance and Maintenance System Hardware Device Manager Monitors After deleting Plug and Play monitor, find 'Plug and Play monitor' by searching new Hardware. MagicTuneTM is an additional software for the monitor. Some graphic cards may not support your monitor. When you have a problem with the graphic card, visit our website to check the compatible graphic card list provided. http://www. samsung. com/monitor/magictune MagicTuneTM doesn't work properly. Have you changed your PC or video graphic card?Did you install the program? Download the latest program. [. . . ] Disconnect the power cord and then clean the monitor with a soft cloth, using either a cleaning solution or plain water. Do not leave any detergent or scratches on the case. Do not let any water enter the monitor. Self-Test Self-Test Feature Check | Warning Messages | Environment | Useful Tips Your monitor provides a self test feature that allows you to check whether your monitor is functioning properly. Self-Test Feature Check Turn off both your computer and the monitor. Unplug the video cable from the back of the computer. [. . . ]