User manual SAMSUNG SYNCMASTER 204TS

[. . . ] SyncMaster 204Ts Notational Failure to follow directions noted by this symbol could result in bodily harm or damage to equipment. Prohibited Important to read and understand at all times Do not disassemble Disconnect the plug from the outlet Do not touch Grounding to prevent an electric shock Power When not used for extended period of time, set your computer to DPMS. If using a screen saver, set it to the active screen mode. Do not use a damaged or loose plug. ! This may cause an electric shock or fire. Do not pull the plug out by the wire nor touch the plug with wet hands. ! This may cause an electric shock or fire. Use only a properly grounded plug and receptacle. ! An improper ground may cause electric shock or equipment damage. Insert the power plug firmly so that it does not come loose. ! A bad connection may cause fire. Do not excessively bend the plug and wire nor place heavy objects upon them, which could cause damage. ! This may cause an electric shock or fire. Do not connect too many extension cords or plugs to an outlet. ! This may cause fire. Installation Be sure to contact an authorized Service Center when installing your set in a location with heavy dust, high or low temperatures, high humidity, and chemical substances, or where it will be operated for 24 hours continuously such as an airport, train station or etc. Failure to do so may cause serious damage to your set. Put your monitor in a location with low humidity and a minimum of dust. ! Failure to do so may cause an electric shock or fire inside the monitor. Do not drop the monitor when moving it. ! This may cause damage to the product or human body. Install the monitor base in a showcase or shelf so that the end of the base does not project beyond the showcase or shelf. ! Dropping the product may cause damage to the product or personal injury. Do not place the product on an unstable or small surface area. ! Place the product on an even, stable surface, as the product may fall and cause harm to someone walking by, specifically children. Do not place the product on the floor. ! Someone, specifically children could trip over it. Keep any flammable objects such as candles, insecticides or cigarettes away from the product. ! Otherwise, this may cause a fire. Keep any heating devices away from the power cable. ! A melted coating may lead to electric shock or fire. Do not install the product in places with poor ventilation, for instance, a bookshelf, closet, etc. ! Any increase in internal temperature may cause fire. Set down the monitor carefully. ! The monitor could be damaged or broken. Do not place the monitor face down. ! The TFT-LCD surface may be damaged. Installing a wall bracket must be done by a qualified professional. ! [. . . ] (System Tray is Checked) MagicColor mode will be different according to monitor models. MagicZone mode will show if the monitor supports the function. Adjusts the gamma value. Gamma Gamma mode will be different according to monitor models. Some monitor will only support Three modes( Mode1, Mode2, Mode3) Mode 1 : Shows normal gamma Mode 2 : Shows lower gamma(darker) Mode 3 : Shows higher gamma(brighter) Image Tab Definition Adjusts the Fine , Coarse and Position values. i j k l m n Image Setup n Position n Sharpness j k l m j k l m Image Setup Fine : Removes noise such as horizontal stripes. If the noise persists even after Fine tuning, repeat it after adjusting the frequency (clock speed). Coarse : Removes noise such as vertical stripes. Coarse adjustment may move the screen image area. You may relocate it to the center using the Horizontal Control menu. Auto Setup : Auto adjustment allows the monitor to self-adjust to the incoming video signal. The values of fine, coarse and position are adjusted automatically. Adjusts the screen location horizontally and vertically. Position Sharpness Changes the clearance of image. Option Tab Definition You can configure MagicTune using the following options. Preferences Loads the Preferences Dialog Box. Preferences in use will have an "V" in the check box. To turn on or off any Preference, position the cursor over the box and click. - To access the MagicTune menus, click the icon on the [task tray menu]. The menus are not displayed if the [Enable System Tray] is deselected in [Options] ' [Basic Settings]. Select Language - The language chosen affects only the language of the OSD. Source Select Analog Digital Support Tab Definition Shows the Asset ID and the version number of the program, and allows you to use the Help feature. Help Visit the MagicTune website or click to open the Help files (User Manual) if you need any help installing or running MagicTune. The User Manual opens within a basic browser window. Asset ID you can use the server to control the Client monitor. (Server program should be installed to use this program as Client) User Name Shows the user name that is registered in PC. User ID Shows the user ID that is register in PC. Server IP Write down the server IP . Department Write down the department. Location Write down the location. Version Displays the version of MagicTune. Overview | Installation | OSD Mode | Color Calibration | Uninstall | Troubleshooting Color Calibration 1. Color Calibration Color Calibration guides you to get optimal color condition for your monitor. Proceed following 5steps for getting optimal monitor color condition . Control "Brightness control bar" for matching the brightness of control patch and the brightness of background pattern When you detect specific color tone on "Control patch", move the control cursor toward to the direction of the color tone referring to "Color reference Circle". => Adjustment is finished properly, you won't detect any color tone on Control patch. When you finish adjustment for step1, Click "Next" button . [. . . ] However, if the same image is displayed for a long time, a slight difference in electric charge accumulates between the two electrodes which encase the liquid crystal. This may cause the liquid crystal to build up in a certain areas of the display. Thus, the previous image is retained when switching to a new video image. All display products, including LCD, are subject to image retention. [. . . ]