User manual SAMSUNG 400EX DOC(DECLARATION OF CONFORMITY)

[. . . ] Refer servicing to qualified service personnel. · If your monitor does not operate normally - in particular, if there are any unusual sounds or smells coming from it - unplug it immediately and contact an authorized dealer or service. · This may cause an electric shock or a fire. · Do not place any heavy objects on the monitor. · This may cause an electric shock or a fire. · For each hour of looking at the monitor, you should let your eyes rest for 5 minutes. · This will reduce eye fatigue. · Do not use or store inflammable substances near the monitor. · This may cause an explosion or fire. User's Manual Safety Instructions Other · Do not try to move the monitor by pulling on the wire or the signal cable. · This may cause a breakdown, electric shock or a fire due to damage to the cable. · Do not move the monitor right or left by pulling only the wire or the signal cable. · This may cause a breakdown, electric shock or a fire due to damage to the cable. · Never insert anything metallic into the monitor openings. · This may cause an electric shock, fire or injury. User's Manual Introduction (SyncMaster 152B) Unpacking Please make sure the following items are included with your monitor. If any items are missing, contact your dealer. Unpacking D-Sub Cable Quick Setup Guide Power Cord Monitor Warranty Card (Not available in all locations) User's Guide and Driver Installation CD DC-Adapter VESA Mounting Bracket For Multimedia model (Option) Multimedia Speaker Stand Sound Cables User's Manual Introduction (SyncMaster 400EX) Unpacking Please make sure the following items are included with your monitor. If any items are missing, contact your dealer. [. . . ] Check List Is the power cord connected properly?Can you see "No Connection, Check Signal Cable" on the screen?If the power is on, reboot the computer to see the initial screen(the login screen), which can be seen. Solutions Check the power cord connection and supply. If the initial screen (the login screen) appears, boot the computer in the applicable mode (the safe mode for Windows ME/2000/XP) and then change the frequency of the video card. (Refer to the Preset Display Modes) Note: If the initial screen (the login screen) does not appear, contact a service center or your dealer. Can you see "Video mode not supported" on the screen? You can see this message when the signal from the video card exceeds the maximum resolution and frequency that the monitor can properly handle. Adjust the maximum resolution and frequency that the monitor can properly handle. There is no image on the screen. Is the power indicator on the monitor blinking at 1 second intervals? The monitor is in PowerSaver mode. Press a key on the keyboard or move the mouse to activate the monitor and restore the image on the screen. Unlock the OSD by pressing the MENU button for at least 5 seconds. I cannot see the On Screen Display. Have you locked the On Screen Display (OSD) Menu to prevent changes? User's Manual Troubleshooting Check List Symptom The screen shows strange colors or just black and white. Check List Is the screen displaying only one color as if looking at the screen through a cellophane paper?Have the screen colors become strange after running a program or due to a crash between applications?If you have problems in installing the adapter (video) driver, boot the computer in Safe Mode, remove the Display Adapter at the "Control Panel, System, Device Administrator" and then reboot the computer to reinstall the adapter (video) driver. Note: If problems repeatedly occur, contact an authorized service center. User's Manual Troubleshooting Q&A Question How can I change the frequency?Answer Frequency can be changed by reconfiguring the video card. Note that video card support can vary, depending on the version of the driver used. (Refer to the computer or the video card manual for details. ) How can I adjust the resolution? Windows ME/2000/XP: Set the resolution at the Control Panel, Display, Settings. * Contact the video card manufacturer for details. How can I set the Power Saving function? Windows ME/2000/XP: Set the function at BIOS-SETUP of the computer or the screen saver. (Refer to Windows/ Computer Manual). How can I clean the outer case/LCD Panel? Disconnect the power cord and then clean the monitor with a soft cloth, using either a cleaning solution or plain water. Do not leave any remains of the detergent nor scratch the case. Do not allow any water to go inside the monitor. User's Manual Troubleshooting Self-Test Feature Check Your monitor provides a self test feature that allows you to check whether your monitor is functioning properly. Self-Test Feature Check 1. Turn off both your computer and the monitor. Unplug the video cable from the back of the computer. If the monitor is functioning properly, you will see a box with a border and text inside as shown in the following illustration: The three boxes inside the border are red, green and blue. Failure of any of the boxes to appear indicates a problem with your monitor. This box also appears during normal operation if the video cable becomes disconnected or damaged. [. . . ] The relevant TCO'99 requirement permits the inclusion of lead since no replacement has yet been developed. * Bio-accumulative is defined as substances which accumulate within living organisms. ** Lead, Cadmium and Mercury are heavy metals which are Bio-accumulative. User's Manual Information Natural Color · Natural Color Software Program One of the recent problems in using a computer is that the color of the images printed out by a printer or other images scanned by a scanner or a digital camera are not the same as those shown on the monitor. The Natural Color S/W is the very solution for this problem. It is a color administration system developed by Samsung Electronics in association with Korea Electronics & Telecommunications Research Institute (ETRI). [. . . ]