User manual SAMSUNG 400FPN-2 QUICK GUIDE

[. . . ] LCD DISPLAY quick start guide 400DX-2, 400DXN-2, 460DX-2, 460DXN-2 Introduction Package Contents Note Please make sure the following items are included with your LCD Display. If any items are missing, contact your dealer. Contact a local dealer to buy optional items. Checking the Contents of the Package Remove the lock from the package box, as shown in the figure above. Lift up the package box by Check the contents of the holding the grooves on package. Note · · Remove the Styrofoam and vinyl cover. After unpacking the package, make sure to check the contents of the package. [. . . ] Note Applicable to the DX-2 model only. Connecting a DVD Player - Applicable to the DX-2 model only. 1. Connect a set of audio cables between the AV/COMPONENT AUDIO IN [L-AUDIO-R] on the LCD Display and the AUDIO OUT jacks on the DVD player. Connections 2. Connect a Component cable between the BNC/COMPONENT IN [R/Y, G/PB, B/PR] port on the LCD Display and the PR, Y, PB jacks on the DVD player. Note · · · · Select Component for the connection to a DVD player using the SOURCE button on the front of the LCD Display or on the remote control. Note DVI OUT does not support HDCP. Connecting Using a DVI to HDMI Cable Connections 1. Connect the DVI output terminal of a digital output device to the HDMI IN terminal of the LCD Display using a DVI to HDMI cable. Connect the red and white jacks of an RCA to stereo (for PC) cable to the same colored audio output terminals of the digital output device, and connect the opposite jack to the DVI / RGB /HDMI AUDIO IN terminal of the LCD Display. Connecting a DTV Set Top (Cable/Satellite) Box - Applicable to the DX-2 model only. 1. 2. Connect a Component cable between the BNC/COMPONENT IN [R/Y, G/PB, B/PR] port on the LCD Display and the PR, Y, PB jacks on the Set Top Box. Connect a set of audio cables between the AV COMPONENT AUDIO IN [L-AUDIO-R] on the LCD Display and the AUDIO OUT jacks on the Set Top Box. Note · · Select Component for the connection to a DTV Set Top Box using the SOURCE button on the front of the LCD Display or on the remote control. For an explanation of Component video, see your Set Top Box owner's manual. Connecting a DTV Set Top (Cable/Satellite) Box Connections 1. Connect the RGB/COMPONENT IN ports on the monitor to the PR, Y, PB ports on the set-top box using the Component/ D-sub cable. Connect a set of audio cables between the AV COMPONENT AUDIO IN [L-AUDIO-R] on the LCD Display and the AUDIO OUT jacks on the Set Top Box. Note · · Select Component using the SOURCE button on the front of the LCD Display or on the remote control. For an explanation of Component video, see your Set Top Box owner's manual. Connecting to an Audio System 1. Connect a set of audio cables between the AUX L, R jacks on the AUDIO SYSTEM and AUDIO OUT on LCD Display. Connecting a LAN Cable Note · AV input devices such as DVD players, VCRs or camcorders as well as your computer can be connected to the LCD Display. For detailed information on connecting AV input devices, refer to the contents under Adjusting Your LCD Display. The LCD Display 's configuration at the back may vary slightly depending on the LCD Display model. · Connections Connect the LAN cable. Note Applicable to the DXN-2 model only. Connecting a USB device Note · · You can connect USB devices such as a mouse or keyboard. Applicable to the DXN-2 model only. Troubleshooting Self-Test Feature Check Note Check the following items yourself before calling for assistance. Contact a Service Center for problems that you cannot solve by yourself. Self-Test Feature Check 1. Turn off both your computer and the LCD Display. Unplug the video cable from the back of the computer. The figure shown below ("Check Signal Cable") appears on a black background when the LCD Display is working normally even though no video signal is detected: While in the Self-Test mode, the LED power indicator remains green and the figure moves around on the screen. 4. Turn off your LCD Display and reconnect the video cable; then turn on both your computer and the LCD Display If your LCD Display screen remains blank after using the previous procedure, check your video controller and computer system; your LCD Display is functioning properly. Warning Messages You can even view the screen at a resolution of 1920 x 1080. [. . . ] Check the polarities (+/-) of the batteries. Troubleshooting A: A: A: A: Check if the batteries are empty. Check if the power cord is securely connected. Check if a special fluorescent or neon lamp is on in the vicinity. Q&A Q: A: How can I change the frequency?The frequency can be changed by reconfiguring the video card. [. . . ]