User manual SAMSUNG SYNCMASTER 460DX-S QUICK GUIDE (VER.1.0)

[. . . ] LCD DISPLAY quick start guide 460DRN-S, 460DR-S Introduction Package Contents Note Please make sure the following items are included with your LCD Display. If any items are missing, contact your dealer. Contact a local dealer to buy optional items. Note This stand is not for the Floor Standing Type. Checking the Contents of the Package Remove the lock from the package box, as shown in the figure above. Lift up the package box by Check the contents of the holding the grooves on package. [. . . ] For detailed information on connecting AV input devices, refer to the contents under Adjusting Your LCD Display. Connecting AV Devices 1. 3. Connect the port of the DVD, VCR (DVD / DTV Set-Top Box) to the [R-AUDIO-L] port of the LCD Display. Then, start the DVD, VCR or Camcorders with a DVD disc or tape inserted. Select AV using the SOURCE . Connections Note The LCD Display has AV connection terminals to connect AV input devices like DVDs, VCRs or Camcorders. You may enjoy AV signals as long as the LCD Display is turned on. Connecting Using a HDMI Cable Note · · Input devices such as digital DVD are connected to the HDMI terminal of the LCD Display using the HDMI cable. You cannot connect a PC to the HDMI terminal. Connecting Using a DVI to HDMI Cable Connect the DVI output terminal of a digital output device to the HDMI terminal of the LCD Display using a DVI to HDMI cable. Connections Connect the red and white jacks of an RCA to stereo (for PC) cable to the same colored audio output terminals of the digital output device, and connect the opposite jack to the DVI / PC / HDMI AUDIO IN terminal of the LCD Display. Connecting to an Audio System Note · Connect a set of audio cables between the AUX L, R jacks on the AUDIO SYSTEM and AUDIO OUT [L-AUDIO-R] on LCD Display. Connecting a LAN Cable Using a Power cord with Earth · In the event of failure, the earth lead may cause electric shock. Make sure to wire the earth lead in correctly, before connecting the AC power. When un-wiring the earth lead, make sure to disconnect the AC power in advance. Note AV input devices such as DVD players, VCRs or camcorders as well as your computer can be connected to the LCD Display. For detailed information on connecting AV input devices, refer to the contents under Adjusting Your LCD Display. Connections Note Connect the LAN cable. (Applicable to the DRN-S model only) Connecting a USB device Using a Power cord with Earth · In the event of failure, the earth lead may cause electric shock. Make sure to wire the earth lead in correctly, before connecting the AC power. When un-wiring the earth lead, make sure to disconnect the AC power in advance. Note AV input devices such as DVD players, VCRs or camcorders as well as your computer can be connected to the LCD Display. For detailed information on connecting AV input devices, refer to the contents under Adjusting Your LCD Display. Note You can connect USB devices such as a mouse or keyboard. Connections (Applicable to the DRN-S model only) Troubleshooting Self-Test Feature Check Note Check the following items yourself before calling for assistance. Contact a Service Center for problems that you cannot solve by yourself. Self-Test Feature Check 1. Turn off both your computer and the LCD Display. Unplug the video cable from the back of the computer. The figure shown below ("Check Signal Cable") appears on a black background when the LCD Display is working normally even though no video signal is detected: While in the Self-Test mode, the LED power indicator remains green and the figure moves around on the screen. 4. Turn off your LCD Display and reconnect the video cable; then turn on both your computer and the LCD Display If your LCD Display screen remains blank after using the previous procedure, check your video controller and computer system; your LCD Display is functioning properly. Warning Messages You can even view the screen at a resolution of 1360 x 768. However, you will receive the following message for a minute; You can choose to change the screen resolution or stay in the current mode during that time. And if the resolution is more than 85Hz, you will see the black screen because the LCD Display does not support over 85Hz. Note Refer to Specifications > Preset Timing Modes for the resolutions or frequencies supported by the LCD Display. Maintenance and Cleaning 1) Maintaining the LCD Display Case. Clean with a soft cloth after disconnecting the power cord. · · Do not use benzene, thinner or other flammable substances, or a wet cloth. We recommend that a SAMSUNG cleansing agent is used to prevent damage to the screen. 2) Maintaining the Flat Panel Display Screen. Troubleshooting Clean with a soft cloth (cotton flannel) smoothly. [. . . ] 5) Run C:\ghost. exe and choose Local Partition From Image from the menu. Choose the ghost image to update your USB disk with and choose the target disk. 6) When the ghost image update finishes, the set will be rebooted automatically. A: A: A: A: A: Q&A Q: A: How can I change the frequency?The frequency can be changed by reconfiguring the video card. [. . . ]