User manual SAMSUNG SYNCMASTER 460UT-2 QUICK GUIDE

[. . . ] LCD DISPLAY quick start guide 460UTn-2, 460UT-2, 460UTn-B, 460UT-B Introduction Package Contents Checking the Contents of the Package Remove the lock from the package box, as shown in the figure above. Lift up the package box by Check the contents of the holding the grooves on package. Note · · · · · Remove the Styrofoam and vinyl cover. After unpacking the package, make sure to check the contents of the package. Store the packaging box in case you need to move the Product later. If any items are missing, contact your dealer. [. . . ] · Connect the [HDMI IN 1] port on the LCD Display to the HDMI port on the PC using the HDMI cable. Connections Note Select HDMI2 (only with a 460UT-2, 460UT-B model) or HDMI1 as an input source when connected to the PC via an HDMI cable. To obtain normal picture and audio from the PC, HDMI2 (only with a 460UT-2, 460UT-B model) or HDMI1 must be selected before PC is selected in Edit Name. To enable audio when DVI Device is selected, be sure to establish the connection using step ( ). Connect the Audio cable for your LCD Display to the AUDIO port on the back of the LCD Display. Connect the power cord for your LCD Display to the POWER port on the back of the LCD Display. Note Contact a local SAMSUNG Electronics Service Center to buy optional items. Connecting to Other devices Note · AV input devices such as DVD players, VCRs or camcorders as well as your computer can be connected to the LCD Display. For detailed information on connecting AV input devices, refer to the contents under Adjusting Your LCD Display. The LCD Display 's configuration at the back may vary slightly depending on the LCD Display model. · Connecting an External Monitor Connections Connect between the [DVI OUT(LOOPOUT)] port on the LCD Display and the input port on another monitor using a DVI cable. Connect between the [AUDIO OUT] port on the LCD Display and the audio input port on another monitor using a stereo cable. Note Select DVI Mode as an input source for the external monitor connected to [DVI OUT]. Press SOURCE on the product or remote control and select "HDMI1 / HDMI2(only with a 460UT-2, 460UT-B model)" Connecting a DVD Player Connect a RGB to Component cable between the [RGB/COMPONENT IN] port on the LCD Display and the PR, Y, PB jacks on the DVD player. Connect a set of audio cables between the [AV/COMPONENT AUDIO IN [L-AUDIO-R]] on the LCD Display and the AUDIO OUT jacks on the DVD player. Note · · · · Press SOURCE on the product or remote control and select "Component". Then, start the DVD Player with a DVD disc inserted. For an explanation of Component video, consult your DVD manual. Connections Connecting a DTV Set Top (Cable/Satellite) Box Connect a RGB to Component cable between the [RGB/COMPONENT IN] port on the LCD Display and the PR, Y, PB jacks on the Set Top Box. Connect a set of audio cables between the [AV/COMPONENT AUDIO IN [L-AUDIO-R]] on the LCD Display and the AUDIO OUT jacks on the Set Top Box. Note · · Press SOURCE on the product or remote control and select "Component". For an explanation of Component video, see your Set Top Box owner's manual. Connecting to an Audio System 1. Connect a set of audio cables between the AUX L, R jacks on the AUDIO SYSTEM and [AUDIO OUT] on LCD Display. Connections Connecting a LAN Cable 1. Connect the LAN cable between the [LAN] port on the product and the [LAN] port on your PC. Note Applicable to the 460UTn-2, 460UTn-B model only. Connecting a USB devices 1. You can connect USB devices such as a mouse or keyboard. Note Applicable to the 460UTn-2, 460UTn-B model only. Troubleshooting Self-Test Feature Check Note Check the following items yourself before calling for assistance. Contact a Service Center for problems that you cannot solve by yourself. Self-Test Feature Check 1. Turn off both your computer and the LCD Display. Unplug the video cable from the back of the computer. The figure shown below ("No Signal") appears on a black background when the LCD Display is working normally even though no video signal is detected: While in the SelfTest mode, the LED power indicator remains green and the figure moves around on the screen. 4. Turn off your LCD Display and reconnect the video cable; then turn on both your computer and the LCD Display If your LCD Display screen remains blank after using the previous procedure, check your video controller and computer system; your LCD Display is functioning properly. Warning Messages You can even view the screen at a resolution of 1920 x 1080. However, you will receive the following message for a minute; You can choose to change the screen resolution or stay in the current mode during that time. If the resolution is more than 85Hz, you will see the black screen because the LCD Display does not support over 85Hz. Note Refer to Specifications > Preset Timing Modes for the resolutions or frequencies supported by the LCD Display. Maintenance and Cleaning 1) Maintaining the LCD Display Case. Clean with a soft cloth after disconnecting the power cord. Troubleshooting · Do not use benzene, thinner or other flammable substances. 2) Maintaining the Flat Panel Display Screen. Clean with a soft cloth (cotton flannel). [. . . ] Check the polarities (+/-) of the batteries. Troubleshooting A: A: A: A: Check if the batteries are empty. Check if the power cord is securely connected. Check if a special fluorescent or neon lamp is on in the vicinity. Q&A Q: A: How can I change the frequency?The frequency can be changed by reconfiguring the video card. [. . . ]