User manual SAMSUNG 460UTN_UD DOC(DECLARATION OF CONFORMITY)

[. . . ] Contact a local dealer to purchase optional items. After unpacking, you may use the lower part of the package box as a temporary stand for product test or operation check. Unpacking LCD Display Introduction Manuals Quick Setup Guide Warranty Card (Not available in all locations) User's Guide Cables Power Cord D-Sub Cable MagicInfo Software CD, MagicInfo Manual CD (Applicable to the 460UTn-2, 460UTn-B model only) Others Remote Control (BP59-00138B) Sold separately Batteries (AAA X 2) (Not available in all locations) Semi Stand KIT LAN Cable USB Cable (Applicable to the 460UTn-2, 460UTn-B model only) Introduction Sold separately RGB to BNC Cable RGB to COMPONENT Cable Network Box (Applicable to the 460UT-2, 460UT-B model only) Wall Mount KIT TV Tuner Box Your LCD Display Front SOURCE button Switches from PC mode to Video mode. Selects the input source that an external device is connected to. [PC] [DVI] [AV] [Component] [HDMI1] [HDMI2] [DisplayPort] [MagicInfo] [TV] Note · · A TV tuner box (sold separately) must be connected to use the TV. [. . . ] The audio Introduction comes back on if MUTE or - VOL + is pressed in the Mute mode. - This is activated when a TV tuner box is installed. - This is activated when a TV tuner box is installed. MENU RETURN EXIT MagicInfo Opens the on-screen menu and exits from the menu or closes the adjustment menu. Note This button is disabled for products that do not support MagicInfo. Connections Connecting a Computer There are several ways to connect the computer to the monitor. Using the D-sub (Analog) connector on the video card. · Connect the D-sub to the 15-pin, [RGB/COMPONENT IN] port on the back of your LCD Display and the 15 pin D-sub Port on the computer. Using the DVI (Digital) connector on the video card. · Connect the DVI Cable to the [DVI IN] port on the back of your LCD Display and the DVI port on the computer. Using the HDMI (Digital) connector on the video card. · Connect the [HDMI IN 1] port on the LCD Display to the HDMI port on the PC using the HDMI cable. Connections Note Select HDMI2 (only with a 460UT-2, 460UT-B model) or HDMI1 as an input source when connected to the PC via an HDMI cable. To obtain normal picture and audio from the PC, HDMI2 (only with a 460UT-2, 460UT-B model) or HDMI1 must be selected before PC is selected in Edit Name. To enable audio when DVI Device is selected, be sure to establish the connection using step ( ). Connect the Audio cable for your LCD Display to the AUDIO port on the back of the LCD Display. If the resolution is more than 85Hz, you will see the black screen because the LCD Display does not support over 85Hz. Note Refer to Specifications > Preset Timing Modes for the resolutions or frequencies supported by the LCD Display. Maintenance and Cleaning 1) Maintaining the LCD Display Case. Clean with a soft cloth after disconnecting the power cord. Troubleshooting · Do not use benzene, thinner or other flammable substances. 2) Maintaining the Flat Panel Display Screen. Clean with a soft cloth (cotton flannel). · Never use acetone, benzene or thinner. (They may cause flaws or deformation of the screen surface. ) · The user is responsible for any damage caused by using these substances. Symptoms and Recommended Actions Note A LCD Display recreates visual signals received from the computer. Therefore, if there is a problem with the computer or the video card, this can cause the LCD Display to become blank, have poor coloring, become noisy, etc. In this case, first check the source of the problem, and then contact a Service Center or your dealer. Check if the power cord and the video cables are properly connected to the computer. Check if the computer beeps more than 3 times when booting. If you installed a new video card or if you assembled the PC, check if you installed the Adaptor(video). Check if the scanning ratio of the video screen is set to between 50 Hz ~ 85 Hz. [. . . ] (Refer to the Connecting a Computer) A: Q: A: A: Q: A: Check the volume level. If the volume is still too low after turning the control to its maximum, check the volume control on the computer sound card or software program. Adjusts the Treble and Bass to the appropriate levels. Problems related to the Remote Control Note Problems related to the remote control and their solutions are listed. Q: A: The remote control buttons do not respond. [. . . ]