User manual SAMSUNG 460UXN-2 POWER CONSUMPTION GUIDE (VER.1.0)

[. . . ] Contact a local dealer to purchase optional items. Unpacking LCD Display Introduction Manuals Quick Setup Guide Warranty Card (Not available in all locations) User's Guide MagicInfo Software CD, MagicInfo Manual CD (Applicable to the 400UXN-3, 460UXN-3 model only) Cables Power Cord Others D-Sub Cable Remote Control (BP59-00138B) Batteries (AAA X 2) (Not available in all locations) Sold separately Semi Stand KIT LAN Cable USB Cable (Applicable to the 400UXN-3, 460UXN-3 model only) Introduction Sold separately RGB to BNC Cable RGB to Component Cable Network Box (Applicable to the 400UX-3, 460UXN-2 model only) Wall Mount KIT Note TV Tuner Box Accessories that can be purchased with the product vary by country. Your LCD Display Front SOURCE button Switches from PC mode to Video mode. Selects the input source that an external device is connected to. [PC] [DVI] [AV] [Component] [HDMI1] [HDMI2] [DisplayPort] [MagicInfo] [TV] Note · · A TV tuner box (sold separately) must be connected to use the TV. A network box (sold separately) must be connected to use MagicInfo with a 400UX-3, 460UXN-2 model. [. . . ] - This is activated when a TV tuner box is installed. ENTER/PRE-CH This button is used to return to the immediately previous channel. - This is activated when a TV tuner box is installed. MUTE Pauses (mutes) the audio output temporarily. This is displayed on the lower left corner of the screen. The audio comes back on if MUTE or - VOL + is pressed in the Mute mode. - This is activated when a TV tuner box is installed. - This is activated when a TV tuner box is installed. MENU Opens the on-screen menu and exits from the menu or closes the adjustment menu. Note This button is disabled for products that do not support MagicInfo. CH/P RETURN EXIT MagicInfo Connections Connecting a Computer There are several ways to connect the computer to the monitor. Using the D-sub (Analog) connector on the video card. (If not, check your local electronics store. ) If your camcorder is stereo, you need to connect a set of two cables. Connections Connecting Using a HDMI Cable 1. Connect an HDMI cable to [HDMI IN 2 (MAGICINFO)] (only with a 400UX-3, 460UXN-2 model) or [HDMI IN 1] on the product and the HDMI output port on a digital device. Contact a Service Center for problems that you cannot solve by yourself. Self-Test Feature Check 1. Turn off both your computer and the LCD Display. Unplug the video cable from the back of the computer. The figure shown below ("No Signal") appears on a black background when the LCD Display is working normally even though no video signal is detected: While in the SelfTest mode, the LED power indicator remains green and the figure moves around on the screen. 4. Turn off your LCD Display and reconnect the video cable; then turn on both your computer and the LCD Display If your LCD Display screen remains blank after using the previous procedure, check your video controller and computer system; your LCD Display is functioning properly. Warning Messages You can even view the screen at a resolution of 1920 x 1080. However, you will receive the following message for a minute; You can choose to change the screen resolution or stay in the current mode during that time. If the resolution is more than 85Hz, you will see the black screen because the LCD Display does not support over 85Hz. Note Refer to Specifications > Preset Timing Modes for the resolutions or frequencies supported by the LCD Display. Maintenance and Cleaning 1) Maintaining the LCD Display Case. Clean with a soft cloth after disconnecting the power cord. Troubleshooting · Do not use benzene, thinner or other flammable substances. 2) Maintaining the Flat Panel Display Screen. Clean with a soft cloth (cotton flannel). · Never use acetone, benzene or thinner. (They may cause flaws or deformation of the screen surface. ) · The user is responsible for any damage caused by using these substances. Symptoms and Recommended Actions Note A LCD Display recreates visual signals received from the computer. [. . . ] (Refer to the Connecting a Computer) A: Q: A: A: Q: A: Check the volume level. If the volume is still too low after turning the control to its maximum, check the volume control on the computer sound card or software program. Adjusts the Treble and Bass to the appropriate levels. Problems related to the Remote Control Note Problems related to the remote control and their solutions are listed. Q: A: A: A: A: The remote control buttons do not respond. [. . . ]