User manual SAMSUNG SYNCMASTER 460UXN-UD QUICK GUIDE (VER.1.0)

[. . . ] SyncMaster 400UXn, 460UXn LCD Monitor User Manual Introduction -- 400UXn -Package Contents Note Please make sure the following items are included with your LCD Display. If any items are missing, contact your dealer. Contact a local dealer to buy optional items. Note This stand is not for the Floor Standing Type. Unpacking LCD Display Manuals Quick Setup Guide Warranty Card (Not available in all locations) User's Guide Cables D-Sub Cable Power Cord Introduction Others Remote Control Batteries (AAA X 2) (Not available in all locations) BNC to RCA Adaptor Jack Sold separately DVI Cable Wall Mount KIT Semi Stand KIT Calibrater BNC Cable LAN Cable For more information on the use of the calibrater, see Natural Color Expert Help. -- 400UXn -Your LCD Display Front MENU button [MENU] Introduction Opens the on-screen menu and exits from the menu. [. . . ] Changes the source of the PIP window signal. Swaps the contents of the PIP and main image. The image in the PIP window will appear on the main screen, and the main screen image will appear in the PIP window. 28. SWAP Introduction Switches the PIP Picture Size. Rewind Stop Play/Pause Fast forward 29. 33. SIZE REW STOP PLAY / PAUSE FF -- 460DXn -Mechanical Layout Mechanical Layout NETWORK MODEL SIZE LCD Display Head NETWORK MODEL SIZE Introduction Installation VESA Bracket · · When installing VESA, make sure to comply with the international VESA standards. Purchasing VESA Bracket and Installation Information : Please contact your nearest SAMSUNG Distributor to place an order. After your order is placed, installation professionals will visit you and install the bracket. At least 2 persons are needed in order to move the LCD Display. SAMSUNG is not responsible for any product damage or any injury caused by installation at customer's discretion. · · Dimensions Notice For securing the bracket on a wall, use only machine screws of 6 mm diameter and 8 to 12 mm length. Wall Bracket Installation · · · Contact a technician for installing the wall bracket. SAMSUNG Electronics is not responsible for any damages to the product or harm to customers when the installation is done by the customer. This product is for installing on cement walls. The product may not stay in place when installed on plaster or wood. Components Only use the components and accessories shipped with the product. Introduction Wall Bracket(1) Hinge(Left 1, Right Plastic 1) Hanger (4) Screw (A)(11) Screw(B) Anchor (4) (11) Wall Bracket Assembly Note There are two hinges(left and right). Insert and tighten the Captive Screw in the direction of the arrow. When done, mount the wall bracket on the wall. There are two hinges(left and right). Captive Screw Wall Bracket Hinge (Left) Hinge (Right) Before drilling into the wall, check if the length between the two locking holes at the back of the product is correct. If the length is too short or long, loosen all or some of the 4screws on the wall bracket to adjust the length. Introduction A3. Length between the two locking holes Check the installation diagram and mark the drill points on the wall. Use the 5. 0 mm bit to drill holes deeper than 35 mm. Fix each anchor in the corresponding hole. Match each of the brackets and hinge holes to the corresponding anchor holes and insert and tighten the 11 screws A. To mount the product on the wall bracket The shape of the product may vary depending on the model. (The assemblies of the plastic hanger and the screw are the same) 1. Remove the 4 screws on the back of the product. Introduction 2. Insert the screw B into the plastic hanger. Notice · · · 3. [. . . ] Choose the ghost image to update your USB disk with and choose the target disk. 6) When the ghost image update finishes, the set will be rebooted automatically. Q&A Q: A: How can I change the frequency?The frequency can be changed by reconfiguring the video card. Note that video card support can vary, depending on the version of the driver used. [. . . ]