User manual SAMSUNG SYNCMASTER 570S-TFT

[. . . ] SyncMaster 570S TFT 580S TFT Flat Panel Monitor Owner's Instructions Information in this document is subject to change without notice. Reproduction in any manner whatsoever without the written permission of Samsung Electronics Co. , Ltd. shall not be liable for errors contained herein or for incidental or consequential damages in connection with the furnishing, performance, or use of this material. The Samsung logo and SyncMaster are registered trademarks of Samsung Electronics Co. , Ltd. ; Microsoft, Windows and Windows NT are registered trademarks of Microsoft Corporation; VESA, DPMS and DDC are registered trademarks of Video Electronics Standard Association; the ENERGY STAR name and logo are registered trademarks of the U. S. [. . . ] After selecting a function, use the "" and "+" buttons to make the adjustments. The setting slidebar moves and the numeric value indicator changes to reflect your adjustments. NOTE: The numeric value indicator is provided as a point of reference only and does not reflect any measureable value. 5 Push the EXIT button once or twice to return to the main menu to select another function or push the EXIT button 1 to 3 times to exit from the OSM. OSM functions and adjustments Table 2. Screen controls Icon Menus and Sub-menus Function Descriptions + Brightness AUTO EXIT MENU AUTO EXIT MENU Contrast AUTO EXIT MENU AUTO EXIT MENU 13 English Adjusting Your FPD Table 2. Screen controls (Continued ) Icon Menus and Sub-menus Function Descriptions + Image Lock: Image Lock controls adjust for and limit the amount of noise in the video signal which causes horizontal lines or areas on the screen where the image appears to be unstable and jitters or shimmers. The Fine and Coarse adjustments allow you to more closely adjust your monitor to your preference. Use the "" and "+" buttons to adjust away interference. If satisfactory results are not obtained using the Fine adjustment, use the Coarse adjustment and then use Fine again. This function may change the width of the display image. Use the H-Position menu to center the display image on the screen. n n Fine Coarse H-Position AUTO EXIT MENU AUTO EXIT MENU V-Position AUTO EXIT MENU AUTO EXIT MENU 14 Adjusting Your FPD Table 2. Screen controls (Continued ) Icon Menus and Sub-menus Function Descriptions + Reset Restores the viewing area and color settings to their original manufacturing levels Resets the H-Position and V-Position of the viewing area Resets the Brightness, Contrast and Color Control functions Select the Color Mode you find most comfortable and then fine tune the colors using the Color Control menus Sets the color to the natural characteristics of the FPD Sets the color to a warm (reddish) white Sets the color to a cool (bluish) white Adjusts the saturation of Red, Green and Blue in the display area Decreases redness Decreases greenness Decreases blueness Increases redness Increases greenness Increases blueness n Geometry Reset Color Reset n Color Temperature n n n Mode 1 Mode 2 Mode 3 Color Control n n n R(ed) G(reen) B(lue) 15 English Adjusting Your FPD Table 2. Screen controls (Continued ) Icon Menus and Sub-menus Function Descriptions + Language: n n n n n n English Deutsch Espaol Franais Italiano Svenska Language sets the OSM to display in one of six languages. The language chosen affects only the language of the OSM. It has no effect on any software running on the computer. Menu Position Each time the OSM opens it displays in the same location on the screen. Menu Position controls that location. n H-Position AUTO EXIT MENU AUTO EXIT MENU n V-Position AUTO EXIT MENU AUTO EXIT MENU Menu Display Time: n n n n 5 Seconds 10 Seconds 20 Seconds 200 Seconds The OSM stays active for as long as it is in use. Menu Display Time sets the length of time the OSM will remain active after the last time you pushed a button. 16 Adjusting Your FPD Table 2. Screen controls (Continued ) Icon Menus and Sub-menus Function Descriptions + i Display Mode This screen shows the horizontal and vertical frequencies, sync polarity and the display resolution of the images received from the computer or video card. 17 English Adjusting Your FPD Audio Controls 1 ON/OFF VOLUME BASS TREBLE MIC MIN MAX MIN MAX MIN MAX ON OFF 2 3 4 5 Figure 8. Multimedia stand audio controls To access the On/Off, Volume, Bass and Treble functions, rotate the appropriate control button to the right or left to adjust the function. Function Description and adjustments 1 Microphone 2 Volume 3 4 5 Bass On/Off Internal Picks up sound and sends it to the sound card in your PC Turns the sound on and off n Left: Off/ Decrease volume n Right: On/ Increase volume Adjusts the volume of the low sound n Left: Decrease volume n Right: Increase volume Treble Adjusts the volume of the high sound n Left: Decrease volume n Right: Increase volume Mic On/Off Turns the internal microphone on or off. Push the button: n In: Off n Out: On 18 Appendix PowerSaver This monitor has a built-in power management system called PowerSaver. This system saves energy by switching your monitor into a low-power mode when it has not been used for a certain amount of time. The available modes are "On", "Standby", "Sleep", and "Deep Sleep". PowerSaver operates with a VESA DPMS compliant video card installed in your computer. [. . . ] Government Printing Office, Washington, DC 20402, Stock Number 004-000-00345-4. MPR II Compliance This monitor complies with SWEDAC(MPR II) recommendations for reduced electric and magnetic fields. European Notice Products with the CE Marking comply with both the EMC Directive (89/336/EEC), (92/31/EEC), (93/68/EEC) and the Low Voltage Directive (73/23/EEC) issued by the Commission of the European Community. Compliance with these directives implies conformity to the following European Norms: n EN55022 (CISPR 22) Radio Frequency Interference n EN50082-1 : 1992 Electromagnetic Immunity n EN60555-2 (IEC555-2) Power Line Harmonics n EN60555-3 (IEC555-3) Voltage Fluctuations n EN60950 (IEC950) Product Safety. Warning User must use shielded signal interface cables to maintain FCC compliance for the product. Declaration of conformity for products Marked with FCC Logo This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. U. S. A. : Samsung Electronics America (SEA) One Samsung Place Ledgewood, NJ 07852 Tel. [. . . ]