User manual SAMSUNG SYNCMASTER 580STFT 570STFT, (VER.1.0)

[. . . ] 1_E570S580Scov. fm Page i Friday, July 13, 2001 10:42 AM SyncMaster 570S TFT 580S TFT Flat Panel Monitor Owner's Instructions 1_E570S580Scov. fm Page ii Friday, July 13, 2001 10:42 AM For Better Display 1. Adjust computer resolution and screen injection rate (refresh rate) in control panel of computer as described below to enjoy the best quality of picture. You can have an uneven quality of picture in the screen if the best quality of picture is not provided in TFT-LCD. · Resolution: 1024 x 768 · Vertical frequency (refresh rate): 60 Hz 2. [. . . ] After using Auto Adjustment, we recommend that you perfect the image by using the OSM functions. 11 English 4_E570S580Sbody. fm Page 12 Monday, July 16, 2001 2:53 PM Adjusting Your FPD Brightness Brightness 44 Exit : Exit Key Follow these instructions to adjust the brightness of the monitor's display. 1 2 With the menu off, push the "­" or "+" button to display the brightness screen. Push the "+" button to increase the brightness; push the "­" button to decrease the brightness. OSM Lock/Unlock Use this function to secure the current settings so that they cannot inadvertently be changed, while still allowing you to adjust Brightness and Contrast. You can unlock the OSM controls at any time by using the same procedure as described below. 1 Push and hold the MENU button for 5 seconds to Lock or Unlock the controls. When locked, a "LOCKED!" message displays along the bottom of each OSM menu screens except the "Brightness" and "Contrast" screens. On-Screen Menu System (OSM) Function icons Function name Brightness Setting slidebar Numeric value indicator Figure 7. On-Screen Menu (OSM) 12 4_E570S580Sbody. fm Page 13 Monday, July 16, 2001 2:53 PM Adjusting Your FPD Accessing the menu system 1 2 3 4 With the OSM off, push the MENU button to open it and display the main function menu. Use the "­" and "+" buttons to move between the function icons. As you move from one icon to another, the function name changes to reflect the function or group of functions represented by that icon. See the Screen controls table to view a complete list of all the functions available for the monitor. Push the MENU button once to activate the highlighted function then use the "­" and "+" buttons to move to sub-menus, or according to the indicators on the menu, to make your changes. After selecting a function, use the "­" and "+" buttons to make the adjustments. The setting slidebar moves and the numeric value indicator changes to reflect your adjustments. NOTE: The numeric value indicator is provided as a point of reference only and does not reflect any measureable value. 5 Push the EXIT button once or twice to return to the main menu to select another function or push the EXIT button 1 to 3 times to exit from the OSM. OSM functions and adjustments Table 2. Screen controls Icon Menus and Sub-menus Function Descriptions ­ + Brightness AUTO EXIT MENU AUTO EXIT MENU Contrast AUTO EXIT MENU AUTO EXIT MENU 13 English 4_E570S580Sbody. fm Page 14 Monday, July 16, 2001 2:53 PM Adjusting Your FPD Table 2. Screen controls (Continued ) Icon Menus and Sub-menus Function Descriptions ­ + Image Lock: Image Lock controls adjust for and limit the amount of noise in the video signal which causes horizontal lines or areas on the screen where the image appears to be unstable and jitters or shimmers. The Fine and Coarse adjustments allow you to more closely adjust your monitor to your preference. Use the "­" and "+" buttons to adjust away interference. If satisfactory results are not obtained using the Fine adjustment, use the Coarse adjustment and then use Fine again. This function may change the width of the display image. Use the H-Position menu to center the display image on the screen. I I Fine Coarse H-Position AUTO EXIT MENU AUTO EXIT MENU V-Position AUTO EXIT MENU AUTO EXIT MENU 14 4_E570S580Sbody. fm Page 15 Monday, July 16, 2001 2:53 PM Adjusting Your FPD Table 2. Screen controls (Continued ) Icon Menus and Sub-menus Function Descriptions ­ + Reset Restores the viewing area and color settings to their original manufacturing levels Resets the H-Position and V-Position of the viewing area Resets the Brightness, Contrast and Color Control functions Select the Color Mode you find most comfortable and then fine tune the colors using the Color Control menus Sets the color to the natural characteristics of the FPD Sets the color to a warm (reddish) white Sets the color to a cool (bluish) white Adjusts the saturation of Red, Green and Blue in the display area Decreases redness Decreases greenness Decreases blueness Increases redness Increases greenness Increases blueness I Geometry Reset Color Reset I Color Temperature I I I Mode 1 Mode 2 Mode 3 Color Control I I I R(ed) G(reen) B(lue) 15 English 4_E570S580Sbody. fm Page 16 Monday, July 16, 2001 2:53 PM Adjusting Your FPD Table 2. Screen controls (Continued ) Icon Menus and Sub-menus Function Descriptions ­ + Language: I I I I I I English Deutsch Español Français Italiano Svenska Language sets the OSM to display in one of six languages. The language chosen affects only the language of the OSM. [. . . ] Before making the connection, make sure the voltage rating of the computer convenience outlet is the same as the monitor and that the ampere rating of the computer convenience outlet is equal to or exceeds the monitor voltage rating. For 120 Volt applications, use only UL Listed detachable power cord with NEMA configuration 5-15P type (parallel blades) plug cap. For 240 Volt applications use only UL Listed Detachable power supply cord with NEMA configuration 6-15P type (tandem blades) plug cap. IC Compliance Notice This Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations of ICES-003. Cet appareil Numérique de classe B respecte toutes les exigences du Règlemont ICES-003 sur les équipements produisant des interférences au Canada. User Information Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. [. . . ]