User manual SAMSUNG SYNCMASTER 650TS-2

[. . . ] SyncMaster 650TS-2 LCD Display User Manual The color and the appearance may differ depending on the product, and the specifications are subject to change without prior notice to improve the performance. Safety Instructions Notational Note These safety instructions must be followed to ensure your safety and prevent property damage. Make sure to read the instructions carefully and use the product in the correct manner. Warning / Caution Failure to follow directions noted by this symbol could result in bodily harm or damage to the equipment. Note Prohibited Important to read and understand at all times Disconnect the plug from the outlet Ground to prevent an electric shock Do not disassemble Do not touch Power When not used for extended period of time, set your computer to DPM. If using a screen saver, set it to active screen mode. [. . . ] Off Cool Normal Warm Custom Note If you set the Color Tone to Cool, Normal, Warm, or Custom, the Color Temp. If you set the Color Tone to Off, the Color Control function is disabled Color Control Adjusts individual Red, Green, Blue color balance. (Not available when Dynamic Contrast is set to On. ) Note If you adjust the picture by using the Color Control function, Color Tone will turn to the Custom mode. Red Green Blue Color Temp. Color Temp. is a measure of the 'warmth' of the image colors. (Not available when Dynamic Contrast is set to On. ) Note This function is only enabled if the Color Tone is set to Off. Adjusting the LCD Display Image Lock Image Lock is used to fine-tune and get the best image by removing noise that creates unstable images with jitters and shakiness. If satisfactory results are not obtained using the Fine adjustment, use the Coarse adjustment and then use Fine again. (Available in PC mode only) Coarse Removes noise such as vertical stripes. Coarse adjustment may move the screen image area. You may relocate it to the center using the horizontal control menu. Fine Removes noise such as horizontal stripes. If the noise persists even after Fine tuning, repeat it after adjusting the frequency (clock speed). Position Adjusts the screen location horizontally and vertically. Auto Adjustment The values of Fine, Coarse, Position are adjusted automatically. By changing the resolution in the control panel, the auto function is performed. (Available in PC mode only) Signal Balance This is used to make up for the weak RGB signal transmitted by a long signal cable. (Not available when Dynamic Contrast is set to On. ) (Available in PC mode only) Adjusting the LCD Display Signal Balance Selects either On or Off with the signal control. Signal Control 1. R-Gain 2. G-Gain 3. B-Gain 4. R-Offset 5. G-Offset 6. B-Offset Size The Size can be switched. 16:9 4:3 Adjusting the LCD Display HDMI Black Level When watching with a DVD or set-top box connecting to the product via HDMI or DVI, image quality deterioration (black level, lower-quality contrast, lighter color tone, etc. ) may occur depending on the connected external device. Normal Low Note · For Timing which can be used for both the PC and the DTV in DVI, HDMI mode, HDMI Black Level will be activated. PIP Picture Adjusts the PIP Screen Settings. Available Modes: PIP ON Contrast Adjusts the Contrast of the PIP window on the screen. Brightness Adjusts the Brightness of the PIP window on the screen. Sharpness Adjusts the Sharpness of the PIP window on the screen. Color Adjusts the Color of the PIP window on the screen. Adjusting the LCD Display Note Enabled only when the PIP input is selected in AV, HDMI or Component mode. Tint Adds a natural tone to the PIP window. Note Enabled only when the PIP input is selected in AV, HDMI or Component mode. [. . . ] Unit: kHz Showing the horizontal lines of the screen from the top to the bottom sequentially is called the Non-Interlace method while showing odd lines and then even lines in turn is called the Interlace method. The Non-Interlace method is used for the majority of monitors to ensure a clear image. The Interlace method is the same as that used in TVs. This is a function that provides the best quality screen for the user by allowing the computer and the monitor to exchange information automatically. [. . . ]