User manual SAMSUNG SYNCMASTER 700DX-3

[. . . ] SyncMaster 700DX-3 LCD Display User Manual The color and the appearance may differ depending on the product, and the specifications are subject to change without prior notice to improve the performance. Safety Instructions Notational Note These safety instructions must be followed to ensure your safety and prevent property damage. Make sure to read the instructions carefully and use the product in the correct manner. Warning / Caution Failure to follow directions noted by this symbol could result in bodily harm or damage to the equipment. Note Important to read and understand at all times Disconnect the plug from the outlet Ground to prevent an electric shock Prohibited Do not disassemble Do not touch An administration fee may be charged if either · (a) an engineer is called out at your request and there is no defect in the product (i. e. where you have failed to read this user manual). [. . . ] In the Edit Group window displayed, click Rename. 3 If a cursor appears in the old group name, enter a new group name. Schedule Management Creating Schedules Create and register a schedule on a group basis. 1 Click All Schedule List in the schedule section on the left side of the program window. The Add button will be enabled in the middle. 2 Click the Add button. The Add Schedule window will appear. 3 Click Add below the Device Group item, and select the group you want to add a schedule to. 4 Select Date&Time/Action and click OK. The schedule will be added and a list of schedules will appear in the set list window. z Device Group: Select a group. Date&Time z Instant Execution: Run the schedule immediately. Timer Set the date, time and interval to run the schedule. z Action: Select a function that will activate at the specified time and interval. Schedule Modification To modify a schedule, select the schedule and click Edit. Deleting a Schedule To delete a schedule, select the schedule and click Delete. Troubleshooting Guide Issue The display you want to control does not appear on the system information chart. Solution Check the connection of the RS232C cable (check that the cable is properly connected to appropriate serial port). Check that another display with a duplicate ID is not connected. Connecting displays with a duplicate ID can cause the displays not to be shown due to data collision. Check that the display ID is within the range of 0 and 99. (Change the ID using the Display menu. ) For a display that supports the ID in a range of 0 to 99, the ID should be set between 0 and 99. 3. The display you want to control does not appear on the other Control Info Grids. The following message appears repeatedly. Check that the display is powered on. (See the power status in the system information chart. ) Ensure you select the input source the display is connected to. Check that the display you want to control is selected. Displays power on or off at different time from one another even though On Time or Off Time is set. The remote control does not work. Adjust the time on the PC to synchronize the time between the connected displays. The remote control may not work if the RS-232C cable is removed or the program is closed abnormally while the Remote Control function is Disable. To resolve this, run the program again and set Remote Control to Enable. This program may malfunction sometimes due to a communication problem between the PC and display or electromagnetic waves emitted from nearby electronic devices. How display properties are shown when multiple displays are used 1 2 3 4 When no display is selected: The default value is displayed. When one display is selected: Settings for the selected display are displayed. in sequence of ID 1 andID 3): The settings for ID 1 are displayed before the settings for ID 3. When the All+Select checkbox is checked and all displays are selected: The default settings are displayed. Adjusting the LCD Display Input Available Modes · · · · · · PC / DVI / DisplayPort AV Component HDMI MagicInfo TV Note A TV tuner box (sold separately) must be connected to use the TV. (US Only) MagicInfo can only be enabled when a network box(sold separately) is connected. Source List Use to select PC, HDMI or other external input sources connected to the LCD Display. [. . . ] The Interlace method is the same as that used in TVs. This is a function that provides the best quality screen for the user by allowing the computer and the monitor to exchange information automatically. This monitor follows the international standard VESA DDC for the Plug & Play function. The number of horizontal and vertical dots used to compose the screen image is called the 'resolution'. [. . . ]