User manual SAMSUNG 700DXN-2 POWER CONSUMPTION GUIDE (VER.1.0)

[. . . ] The images here are for reference only, and are not applicable in all cases (or countries). Do not use a damaged or loose plug. This may cause electric shock or fire. Do not pull the plug out by the wire nor touch the plug with wet hands. This may cause electric shock or fire. Use only a properly grounded plug and receptacle. An improper ground may cause electric shock or equipment damage. (Class l Equipment only. ) Insert the power plug firmly so that it does not come loose. A bad connection may cause fire. Do not excessively bend the plug and wire nor place heavy objects upon them, which could cause damage. This may cause electric shock or fire. Do not connect too many extension cords or plugs to one outlet. This may cause fire. Do not disconnect the power cord while using the LCD Display. A surge may be caused by the separation and may damage the LCD Display. Do not use the power cord when the connector or plug is dusty. If the connector or plug of the power cord is dusty, clean it with a dry cloth. Using the power cord with a dusty plug or connector may cause electric shock or fire. To disconnect the apparatus from the mains, the plug must be pulled out from the mains socket, therefore the mains plug shall be readily operable. This may cause electric shock or fire. Installation Be sure to contact an authorized the Service Center, when installing your LCD Display in a location with heavy dust, high or low temperatures, high humidity, and exposed to chemical substances and where it operates for 24 hours such as at airports, train stations etc. Failure to do so may cause serious damage to your LCD Display. Place your LCD Display in a location with low humidity and a minimum of dust. Failure to do so may cause electric shock or fire inside the LCD Display. Do not drop the LCD Display when moving it. This may cause damage to the product or the person carrying it. Install the LCD Display base in a showcase or shelf so that the end of the base does not protrude from the showcase or shelf. Dropping the product may cause damage to the product or the person carrying it. Do not place the product on an unstable or small surface area. Place the product on an even and stable surface , as the product may fall and cause harm to someone walking by, specifically children. Do not place the product on the floor. Take care, as someone, specifically children may trip over it. TO PREVENT THE SPREAD OF FIRE, KEEP CANDLES OR OTHER OPEN FLAMES AWAY FROM THIS PRODUCT AT ALL TIMES. Otherwise, this may cause fire. Keep any heating devices away from the power cable. A melted coating may cause electric shock or fire. Do not install the product in places with poor ventilation, for instance, a bookshelf, closet, etc. Any increase in the internal temperature may cause fire. Put down the LCD Display carefully. Failing to do so may damage the LCD Display. Do not place the LCD Display face down. This may damage the TFT-LCD surface. The installation of the bracket must be done by a qualified professional. Installing the bracket by unqualified personnel may result in injury. Always use the mounting device specified in the owner's manual. When installing the product, make sure to keep it away from the wall (more than 10 cm / 4 inches) for ventilation purposes. Poor ventilation may cause an increase in the internal temperature of the product, resulting in a shortened component life and degraded performance. Keep the plastic packaging (bag) out of children's reach. The plastic packaging (bag) may cause suffocation if children play with it. Clean When cleaning the LCD Display case or the surface of the TFT-LCD screen, wipe with a slightly moistened, soft fabric. Do not spray water or detergent directly onto the LCD Display. This may cause damage, electric shock or fire. Use the recommended detergent with a smooth cloth. If the connector between the plug and the pin is dusty or dirty, clean it properly using a dry cloth. A dirty connector may cause electric shock or fire. Make sure to unplug the power cord before cleaning the product. Otherwise, this may cause electric shock or fire. Unplug the power cord from the power outlet and wipe the product using a soft, dry cloth. Do not use any chemicals such as wax, benzene, alcohol, thinners, insecticide, air freshener, lubricant or detergent. Others Do not remove the cover (or back). This may cause electric shock or fire. Refer to a qualified servicing company. If your LCD Display does not operate normally - in particular, if there is any unusual sound or smell coming from the LCD Display unplug it immediately and contact an authorized dealer or the Service Center. This may cause electric shock or fire. Keep the product away from places exposed to oil, smoke or moisture; do not install inside a vehicle. This may cause a malfunction, electric shock or fire. [. . . ] Total Publishing Size: Indicates the total size of all the screens within the specified publishing period. This is the total size of the files whose play mode is set to Download in all screens. However, for a local monitor, the size of the files whose play mode is set to Stream is included too. Free Space: Indicates the size of the files the monitor can download while publishing. If the total publishing size is larger than the free size, publishing cannot be performed. However, if you change the Maximum Publishing Size option in the Schedule tab in the Server Option, schedules can be published regardless of the available free size. Status: Displays the publishing progress as a percentage on the slide bar. This is the percentage of the size of the files downloaded to the monitor compared to the total screen (file) size. Result: Displays the publishing results. Double-click the schedule or click this button to view the detailed publishing information. What is MagicNet?Remote Management | | Using MagicNet Message | | Library Option | | Screen Client / Contents Server | | Schedule Troubleshooting Remote Management File Menu Library / Screen / Schedule / Remote Management / Message Creates a view or selects a created view for each menu item so that you can perform a screen schedule and have basic control over the monitors from the server. Time : Sets the current time and displays the state of the on and off timers. You can control each item by clicking on it and changing the setting in the list view. -Current Time 1) Hour: Enter the hour. 3) AM/PM: Enter AM or PM. -On Timer 1) 2) 3) 4) 5) 6) Hour: Enter the hour. Status: Select whether to use the turn-on time. Source: Select the external input Volume: Select the volume -Off Timer 1) 2) 3) 4) Hour: Enter the hour. Status: Select whether to use the turn-on time. PIP: Displays the PIP information. Sound: Displays the current sound state. Signal Balance: Displays the current signal balance state. Maintenance: Displays the Lamp Control, Safety Screen, Video Wall, VideoWall Format, and Safety Lock state. Diagnosis: Displays whether each client is normal or not. [. . . ] They are divided into Vertical and Horizontal Sync Signals. These signals display normal color images by the set resolution and frequency. Types of Sync Signals Separate Composite This is a scheme of transmitting individual vertical sync signals to the LCD Display. This is a scheme of combining vertical sync signals into one composite signal and transmitting it to the LCD Display. [. . . ]