User manual SAMSUNG SYNCMASTER 757DFX

[. . . ] User's Manual 2 Index Main Page On-Screen Display General Highlight Zone MouScreenTM S/W Safety Instructions Natational Power Installation Cleaning Other Introduction Unpacking Front Rear Bottom Setup Connecting Your Monitor Installing the Monitor Driver -- Windows 2000 -- Other Operating System Base Installation Information Service Terms Regulatory Natural Color MouScreenTM S/W Authority Specifications General Specifications Preset Display Modes PowerSaver Troubleshooting Check List Q&A Self-Test Feature Check User's Manual 3 Safety Instructions Notational Warning/Caution Failure to follow directions noted by this symbol could result in bodily harm or damage to equipment. Notation Conventions Prohibited Important to read and understand at all times Do not disassemble Disconnect the plug from the outlet Do not touch Grounding to prevent an electric shock User's Manual 4 Safety Instructions Power When not used for extended periods of time, set your PC to DPMS. If using a screen saver, set it to the active screen mode. If the size of your monitor is small, or if the same image is present for long periods of time, you may see afterimages due to damage to the flourescent substance on the inside of the CDT. · Do not use a damaged or loose plug. · This may cause an electric shock or fire. · Do not pull the plug out by the wire nor touch the plug with wet hands. · This may cause an electric shock or fire. · Use only a properly grounded plug and recepticle. · An improper ground may cause electric shock or equipment damage · Do not excessively bend the plug and wire nor place heavy objects upon them, which could cause damage. · Failure to do so may cause an electric shock or fire. User's Manual 5 Safety Instructions Power · Disconnect the plug from the outlet during storms or lightening or if it is not used for a long period of time. · Failure to do so may cause an electric shock or fire. · Do not connect too many extension cords or plugs to an outlet. · This may cause a fire. User's Manual 6 Safety Instructions Installation · Do not cover the vents on the monitor cabinet. · Bad ventilation may cause a breakdown or fire. · Put your monitor in a location with low humidity and a minimum of dust. · An electric shock or fire could result inside the monitor. · Do not drop the monitor when moving it. · This may cause damage to the product or human body. · Place the monitor on a flat and stable surface. · The monitor can cause injury by falling. · Set down the monitor carefully. · It could be damaged or broken. User's Manual 7 Safety Instructions Installation · Do not place the monitor face down. · The CDT surface may be damaged. · Do not use the monitor without the monitor stand. · · It could break down or cause a fire due to bad ventilation. If the monitor must be used without the supplied stand, take steps to insure proper ventilation. User's Manual 8 Safety Instructions Clean When cleaning the monitor case or the surface of the CDT, wipe with a slightly moistened, soft fabric. [. . . ] Zoom Use this to enlarge or reduce the Highlight Zone. You cannot use this function if the Highlight Zone Full Screen function is on. Sharpness Use this to adjust the layout of the Highlight Zone clearly. Highlight Zone Full Screen Enlarge the Highlight Zone to the full screen. Highlight Zone On/Off You can turn on or off the Highlight Zone by selecting the Highlight Zone checkbox from the Highlight Zone tab. You can select functions in the Highlight Zone tab only when the Highlight Zone is turned on. User's Manual 45 On-Screen Display MouScreen More 1. Moire Use this to remove circle or arc wavy patterns. Side Pin Corner Use this to keep the side pins of the screen facing the opposite direction. Side Pin Balance Use this to keep the side pins of the screen facing the same direction. 4. Degauss Use this to remove spots on the screen, which are caused due to magnetic fields. User's Manual 46 On-Screen Display MouScreen Other 1. Recall Use this to undo the modified content in the current tab. However, there is no Recall function in the Highlight Zone tab. Save Use this to save the updated content in the current tab. Reset Use this to make the current status of the monitor the same as the status when you bought it. This may take time, as it needs to bring and process all the initial data. Save All Use this to save all the updated tab status. Saving all the data may take time. User's Manual 47 Troubleshooting Check List Before calling for service, check the information in this section to see if you can remedy any problems yourself. If you do need assistance, please call the phone number on the warranty card, the phone number on the Information section or contact your dealer. Symptom No images on the screen. I cannot turn on the monitor. Check List Is the power cord connected properly?Can you see "No Connection, Check Signal Cable" on the screen?If the power is on, reboot the computer to see the initial screen(the login screen), which can be seen. Solutions Check the power cord connection and supply. Check the signal cable connection. If the initial screen (the login screen) appears, boot the computer in the applicable mode (the safe mode for Windows 98/95) and then change the frequency of the video card. [. . . ] This system is available only for Samsung monitors and makes the color of the images on the monitor the same as the printed or scanned images. For more information, refer to Help (F1) in the software program. How to install the Natural Color software Insert the CD included with the Samsung monitor into the CD-ROM Drive. Then, the initial screen of the program installation will be executed. [. . . ]