User manual SAMSUNG SYNCMASTER 760VTFT

[. . . ] SyncMaster 760TFT/760VTFT/171V Main Page On-Screen Display Safety Instructions Notational Power Installation Cleaning Other Troubleshooting Check List Q&A Self-Test Feature Check Introduction Unpacking Front Rear Specifications General Specifications PowerSaver Preset Display Modes Setup Connecting Your Monitor Installing the Monitor Driver Automatic Manual Installing VESA compliant mounting Information Service Terms Regulatory Natural Color For Better Display Authority Notational Power Installation Clean Other Failure to follow directions noted by this symbol could result in bodily harm or damage to equipment. Prohibited Important to read and understand at all times Do not disassemble Disconnect the plug from the outlet Do not touch Grounding to prevent an electric shock Notational When not used for extended periods of time, set your PC to DPMS. If using a screen saver, set it to the active screen mode. Power Installation Clean Other Do not use a damaged or loose plug. This may cause an electric shock or fire. Do not pull the plug out by the wire nor touch the plug with wet hands. This may cause an electric shock or fire. Use only a properly grounded plug and recepticle. [. . . ] The values of fine, coarse and position are adjusted automatically. Push the Auto button. To make the automatic adjustment function sharper, execute the 'AUTO' function while the AUTO PATTERN is on. OSD Lock/Unlock 1. Push and hold in the Menu ( or more to Lock the OSD. Push and hold in the Menu ( or more to Unlock the OSD. ) button for 5 seconds ) button for 5 seconds Before calling for service, check the information in this section to see if you can remedy any problems yourself. If you do need assistance, please call the phone number on the warranty card, the phone number on the Information section or contact your dealer. Check List Q&A Self-Test Feature Check Symptom No images on the screen. I cannot turn on the monitor. Check List Is the power cord connected properly?Can you see "No Connection, Check Signal Cable" on the screen?If the power is on, reboot the computer to see the initial screen(the login screen), which can be seen. Solutions Check the power cord connection and supply. Check the signal cable connection. If the initial screen (the login screen) appears, boot the computer in the applicable mode (the safe mode for Windows 95/98/ME/XP/2000 and then change the frequency of the video card. (Refer to the Preset Display Modes) Note: If the initial screen (the login screen) does not appear, contact a service center or your dealer. Can you see "Video mode not supported" on the screen? You can see this message when the signal from the video card exceeds the maximum resolution and frequency that the monitor can properly handle. Adjust the maximum resolution and frequency that the monitor can properly handle. There is no image on the screen. Is the power indicator on the monitor blinking at 1 second intervals? The monitor is in PowerSaver mode. Press a key on the keyboard or move the mouse to activate the monitor and restore the image on the screen. Unlock the OSD by pressing the MENU button for at least 5 seconds. I cannot see the On Screen Display. Have you locked the On Screen Display (OSD) Menu to prevent changes? The screen is out of focus or OSD cannot be adjusted. Check List Q&A Self-Test Feature Check Have you adjusted the resolution or frequency on the monitor?Is the frequency properly adjusted when checking the Display Timing on the menu? Adjust the resolution and frequency of the video card. Adjust the frequency properly by referring to the video card manual and the Preset Display Modes. (The maximum frequency per resolution may differ from product to product. ) LED is blinking but no images on the screen. There are only 16 colors shown on the screen. The screen colors have changed after changing the video card. Have the Windows colors been set properly? For Windows 95/98/ME/XP/2000: Set the colors properly at the Control Panel, Display, Settings. For Windows 3. 1: Adjust the colors of the screen using the VGA utility provided by the video card. Has the video card been set properly? [. . . ] Click Natural Color on the initial screen to install the Natural Color software. To install the program manually, insert the CD included with the Samsung monitor into the CD-ROM Drive, click the [Start] button of Windows and then select [Execute]. Enter D:\color\eng\setup. exe and then press the <Entrer> key. (If the drive where the CD is inserted is not D:\, enter the applicable drive. ) How to delete the Natural Color software program Select [Setting]/[Control Panel] on the [Start] menu and then double-click [Add/Delete a program]. [. . . ]