User manual SAMSUNG SYNCMASTER 76BDF

[. . . ] SAMTRON 76BDF / 96P Main > Index Main Page Safety Instructions Notational Power Installation Cleaning Other Introduction Unpacking Front Rear Bottom Setup Connecting Your Monitor Installing the Monitor Driver Automatic Manual Base Installation On-Screen Display Troubleshooting Check List Q&A Self-Test Feature Check Specifications General Specifications Preset Timing Modes PowerSaver Information Service Terms Regulatory Authority Main > Safety Instructions > Notational Notational Power Installation Clean Other Failure to follow directions noted by this symbol could result in bodily harm or damage to equipment. Prohibited Important to read and understand at all times Do not disassemble Disconnect the plug from the outlet Do not touch Grounding to prevent an electric shock Main > Safety Instructions > Power When not used for extended periods of time, set your PC to DPMS. If using a screen saver, set it to the active screen mode. Notational Power Installation Clean Other If the size of your monitor is small, or if the same image is present for long periods of time, you may see afterimages due to damage to the fluorescent substance on the inside of the CRT. Do not use a damaged or loose plug. This may cause an electric shock or fire. Do not pull the plug out by the wire nor touch the plug with wet hands. This may cause an electric shock or fire. Use only a properly grounded plug and recepticle. [. . . ] Do not allow any water to go inside the monitor. The monitor makes a sound when it is turned on. How can I clean the outer case/Picture tube? Main > Troubleshooting > Self-Test Feature Check Self-Test Feature Check | Warning Messages | Environment | Useful Tips Check List Q&A Your monitor provides a self test feature that allows you to check whether your monitor is functioning properly. Self-Test Feature Check 1. Turn off both your computer and the monitor. Unplug the video cable from the back of the computer. If your monitor works normally, the following screen appears. Failure of any of the boxes to appear indicates a problem with your monitor. This box also appears during normal operation if the video cable becomes disconnected or damaged. Turn off your monitor and reconnect the video cable; then turn on both your computer and the monitor. If your monitor screen remains blank after using the previous procedure, check your video controller and computer system; your monitor is functioning properly. If there is something wrong with the input signal, a message appears on the screen or the screen goes blank although the power indicator LED is still on. The message may indicate that the monitor is out of scan range or that you need to check the signal cable. The location and the position of the monitor may influence the quality and other features of the monitor. 1 th f k th it l dl t th ft th 1. If there are any woofer speakers near the monitor, unplug and relocate the woofer to another room. Remove all electronic devices such as radios, fans, clocks and telephones that are within 3 feet (one meter) of the monitor. Degauss the monitor if any devices were removed from the area. A monitor recreates visual signals received from the PC. Therefore, if there is trouble with the PC or the video card, this can cause the monitor to become blank, have poor coloring, noise, Sync. In this case, first check the source of the problem, and then contact a service center or your dealer. Judging the monitor's working condition If there is no image on the screen or an "Sync. Out of Range" message comes up, disconnect the cable from the computer while the monitor is still powered on. If there is a message coming up on the screen or if the screen goes white, this means the monitor is in working condition. In this case, check the computer for trouble. Main > Specifications > General General Model Name General PowerSaver Preset Timing Modes SAMTRON 76BDF Picture Tube Type Deflection angle Dot Pitch Screen type 17"(43cm) DynaFlat X (40. 6cm viewable) 90 ° 0. 20mm (Horizontal) Aluminized tri-color phosphor dot trio with black matrix. Multi-layer coated with anti-static. Maximum Resolution 1600 Dots, 1200 Lines Active Display Horizontal Vertical Synchronization Horizontal Vertical Input Signal Definition Video Signal Sync Signal Display Color Unlimited Maximum Pixel Clock 110 MHz Power Supply 90 ~ 264VAC rms, 60/50 Hz ± 3Hz Power Consumption 90W (Maximum) Dimensions (WxDxH) 398 x 412 x 400mm (with Stand) Weight 15. 7 kg Environmental considerations Operating Temperature 32°F ~ 104°F(0°C ~ 40°C) Humidity 10% ~ 80%, non-condensing Storage Temperature -4°F ~113°F (-20°C ~ 45°C) Humidity 5% ~ 95%, non-condensing Plug and Play Capability This monitor can be installed on any Plug & Play compatible system. Interaction of the monitor and computer systems will provide the best operating conditions and monitor settings. In most cases, monitor installation will proceed automatically, unless the user wishes to select alternate settings. Note: Design and specifications are subject to change without prior notice. RGB, Analog 0. 7 Vpp positive at 75 ohms Separate H/V sync, TTL level, positive or negative 30 ~ 85 kHz 50 ~ 160 Hz 312 ± 4 mm 234 ± 4 mm SAMTRON 96P General Model Name General PowerSaver Preset Timing Modes SAMTRON 96P Picture Tube Type Deflection angle Dot Pitch Screen type 19"(48cm) Full square type (45. 8cm viewable) 90 ° 0. 22mm (Horizontal) Aluminized tri-color phosphor dot trio with black matrix. [. . . ] CFCs (freons) The relevant TCO'99 requirement states that neither CFCs nor HCFCs may be used during the manufacture and assembly of the product. CFCs (freons) are sometimes used for washing printed circuit boards. CFCs break down ozone and thereby damage the ozone layer in the stratosphere, causing increased reception on earth of ultraviolet light with e. g. increased risks of skin cancer (malignant melanoma) as a consequence. [. . . ]