User manual SAMSUNG SYNCMASTER 800TFT

[. . . ] SyncMaster 800TFT TFT-LCD Monitor Owner's Instructions CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. Unpacking your Monitor Please make sure the following items are included with your monitor. If any items are missing, contact your dealer. Power adapter Cable Holder Colorific & Driver Power Cord Warranty Card (Not available in all areas) Monitor and Stand 15-pin D-Sub Signal Cable Manual DC-Adapter 13W3 Signal Cable (Optional) The stand type is subject to change based on monitor. 1 Portu- Italiano Espaol Safety Instructions . 6 Maintenance of Your Flat Panel Display . [. . . ] 9 Italiano Portuguese Caution : For Auto Adjustment to function correctly, the monitor must display a full screen, colored image. Deutsch Follow these instructions to enable or disable the automatic screen adjustments for your FPD. Espaol The features described on this page and the next page can be accessed quickly, at the touch of one button. Franais English Adjusting Your FPD Adjusting Your FPD Contrast Contrast 16 Follow these instructions to adjust the contrast between darkness and lightness on the FPD's display EXIT: Exit key + 1 2 With the menu off, push the "" ( ) or "+" ( ) button. Push the "+" ( ) button to increase the contrast; push the "" ( ) button to decrease the contrast. OSM Lock/Unlock This function allows you to secure the current settings so that they cannot be inadvertently changed, while still allowing you to adjust the Brightness and Contrast. You can unlock the OSM controls at any time by using the same procedure. 1 Push and hold the MENU button for 5 seconds to Lock or Unlock the controls. When locked, a "LOCKED!" message will be displayed along the bottom of each OSM menu until you unlock the controls again. 10 Menu System Image Lock Fine 29 Coarse 1688 Auto Adjustment Access: Menu Key Figure 6. On-Screen Menu (OSM) Accessing the Menu System 1 2 3 4 With the menu off, push the MENU button to open the menu system and display the main function menu. Push the "+" ( ) button to move to the next icon or push the "" ( ) button to move back to the previous icon. As you move from one icon to another, the function name changes to reflect the function or group of functions represented by that icon. See the table below to view a complete list of all the functions offered by this FPD. Push the MENU button once to select the adjustment function, then use the "" ( ) or "+"( ) and the "" ( ) or "+"( ) buttons to make your changes. Push the EXIT button once to return to the main menu to select another function or push the EXIT button 1 or 2 times to exit from the OSM. 11 Italiano Portuguese Deutsch Espaol Franais i English Adjusting Your FPD Adjusting Your FPD Table 1. Menu Adjustments Icon Settings and Sub-menus Image Lock: Fine Coarse Description The Fine and Coarse adjustments allow you to more closely adjust your FPD to your preference. Use the "" ( ) and "+" ( ) buttons to adjust away the interference. If satisfactory results are not obtained using the Fine adjustment, use the Coarse adjustment and then use Fine again. This function may change the width and centering of the display image. Use the Horizontal function on the Position menu to center the display image on the screen. Select this icon to adjust for and limit the amount of noise visible in the displayed image which can appear as horizontal lines or areas on the screen where the image is unstable and jitters or shimmers. Auto Adjustment allows the FPD to self-adjust to the incoming video signal. After using Auto Adjustment you can further tune your FPD to your liking using the Fine and Coarse adjustments. Caution: Using Auto Adjustment will cause any stored user settings to be overwritten. Select this icon to move the viewing area on the FPD screen. Use the "" ( ) and "+" ( ) buttons to move the viewing area to the left or right when Horizontal is selected and up and down when Vertical is selected. Select this icon to adjust the color hue and saturation. [. . . ] Before making the connection, make sure the voltage rating of the computer convenience outlet is the same as the monitor and that the ampere rating of the computer convenience outlet is equal to or exceeds the monitor voltage rating. For 120 Volt applications, use only UL Listed detachable power cord with NEMA configuration 5-15P type (parallel blades) plug cap. For 240 Volt applications use only UL Listed Detachable power supply cord with NEMA configuration 6-15P type (tandem blades) plug cap. Franais English Regulatory Information U. S. A. : Samsung Electronics America (SEA) One Samsung Place Ledgewood, NJ 07852 Tel. [. . . ]