User manual SAMSUNG SYNCMASTER 900NF

[. . . ] SyncMaster 959NF/900NF User's Manual 2 Index Main Page On-Screen Display General Highlight Zone MouScreen S/W Safety Instructions Natational Power Installation Cleaning Other Introduction Unpacking Front Rear Bottom Setup Connecting Your Monitor Installing the Monitor Driver -- Automatic -- Manual Base Installation Information Service Terms Regulatory Natural Color MouScreen Authority S/W Specifications General Specifications Preset Display Modes PowerSaver Troubleshooting Check List Q&A Self-Test Feature Check User's Manual 3 Safety Instructions Notational Warning/Caution Failure to follow directions noted by this symbol could result in bodily harm or damage to equipment. Notation Conventions Prohibited Important to read and understand at all times Do not disassemble Disconnect the plug from the outlet Do not touch Grounding to prevent an electric shock User's Manual 4 Safety Instructions Power When not used for extended periods of time, set your PC to DPMS. If using a screen saver, set it to the active screen mode. If the size of your monitor is small, or if the same image is present for long periods of time, you may see afterimages due to damage to the flourescent substance on the inside of the CDT. · Do not use a damaged or loose plug. · This may cause an electric shock or fire. · Do not pull the plug out by the wire nor touch the plug with wet hands. · This may cause an electric shock or fire. · Use only a properly grounded plug and recepticle. · An improper ground may cause electric shock or equipment damage · Do not excessively bend the plug and wire nor place heavy objects upon them, which could cause damage. · Failure to do so may cause an electric shock or fire. User's Manual 5 Safety Instructions Power · Disconnect the plug from the outlet during storms or lightening or if it is not used for a long period of time. · Failure to do so may cause an electric shock or fire. · Do not connect too many extension cords or plugs to an outlet. · This may cause a fire. User's Manual 6 Safety Instructions Installation · Do not cover the vents on the monitor cabinet. · Bad ventilation may cause a breakdown or fire. · Put your monitor in a location with low humidity and a minimum of dust. · An electric shock or fire could result inside the monitor. · Do not drop the monitor when moving it. · This may cause damage to the product or human body. · Place the monitor on a flat and stable surface. · The monitor can cause injury by falling. · Set down the monitor carefully. · It could be damaged or broken. User's Manual 7 Safety Instructions Installation · Do not place the monitor face down. · The CDT surface may be damaged. · Do not use the monitor without the monitor stand. · · It could break down or cause a fire due to bad ventilation. If the monitor must be used without the supplied stand, take steps to insure proper ventilation. User's Manual 8 Safety Instructions Clean When cleaning the monitor case or the surface of the CDT, wipe with a slightly moistened, soft fabric. [. . . ] You can select menu functions in the Highlight Zone only when the Highlight Zone is turned on. You cannot select menu functions when this setting is off. Highlight Zone on : As soon as you click the On checkbox, the Highlight Zone turns on, while the checkbox appears checked/selected. Highlight Zone off : As soon as you click the Off checkbox, the checkbox will be unchecked and the Highlight Zone turns off. On-Screen Display Highlight Zone Full Screen This setting enlarges the Highlight Zone to full screen mode. Selection and Adjustment : The Highlight Zone changes to Full Screen mode when its checkbox is selected. Icons and other related functions may be selected, irrespective of whether the Highlight Zone is in On or Off mode. When the Highlight Zone is in Full mode, it enlarges to the entire screen area and is locked by the Picture icon because Position/Size adjustment is no longer required. Deactivating Full Highlight Zone : When you click the Full checkbox again, in the Full mode, the Highlight Zone returns to the previous menu. If you wish to turn it off, you may select On/Off at this stage. On-Screen Display Highlight Zone Position/Size Tab(Highlight Zone) This setting adjusts the Highlight Zone's vertical or horizontal location, and shrinks or enlarges its size. Position Adjustment : Place and click your mouse pointer on the Position icon and then drag it as desired. The Highlight Zone moves freely in any direction, following as the mouse is dragged. Size Adjustment : Place and click your mouse cursor on the Size icon and then drag as desired. The Horizontal Size (Width) adjustment icon is located on the left and right sides and the Vertical Size (Height) adjustment icon is located on the top and bottom of the screen. Drag outward, along the grid where the icons are located, to increase the Highlight Zone's Width. Drag upward, along the grid where the icons are located, to increase the Highlight Zone's Height. Zoom Adjustment : Place and click your mouse pointer on the Zoom icon and then drag it as desired. To adjust, drag in the direction of the Zoom icon arrow. Drag outward to increase the Highlight Zone. Drag inward to decrease it. On-Screen Display Highlight Zone Picture Tab(Highlight Zone) This setting complements the contrast, hue and outline of the Highlight Zone. Place and click the mouse pointer on Picture Icon when the Highlight Zone is On. The Picture tab adjusts the Highlight Zone's contrast, color tone and outline. Place your mouse pointer on the arrow for any of the desired menu icons and drag it as desired. [. . . ] Click Natural Color on the initial screen to install the Natural Color software. To install the program manually, insert the CD included with the Samsung monitor into the CD-ROM Drive, click the [Start] button of Windows and then select [Execute]. Enter D:\color\eng\setup. exe and then press the key. (If the drive where the CD is inserted is not D:\, enter the applicable drive. ) How to delete the Natural Color software program Select [Setting]/[Control Panel] on the [Start] menu and then double-click [Add/Delete a program]. [. . . ]