User manual SAMSUNG SYNCMASTER 955DF

[. . . ] SyncMaster 955DF Main Page On-Screen Display General Highlight Zone Safety Instructions Notational Power Installation Cleaning Other Introduction Unpacking Front Rear Bottom Setup Connecting Your Monitor Installing the Monitor Driver Automatic Manual Base Installation Troubleshooting Check List Q&A Self-Test Feature Check Specifications General Specifications Preset Timing Modes PowerSaver Information Service Terms Regulatory Natural Color Authority Notational Power Installation Clean Other Failure to follow directions noted by this symbol could result in bodily harm or damage to equipment. Prohibited Important to read and understand at all times Do not disassemble Disconnect the plug from the outlet Do not touch Grounding to prevent an electric shock When not used for extended periods of time, set your PC to DPMS. If using a screen saver, set it to the active screen mode. Notational Power Installation Clean Other If the size of your monitor is small, or if the same image is present for long periods of time, you may see afterimages due to damage to the fluorescent substance on the inside of the CDT. Do not use a damaged or loose plug. This may cause an electric shock or fire. Do not pull the plug out by the wire nor touch the plug with wet hands. This may cause an electric shock or fire. Use only a properly grounded plug and recepticle. [. . . ] (The maximum frequency per resolution may differ from product to product. ) There are only 16 colors shown on the screen. The screen colors have changed after changing the video card. There is a message that reads "Unrecognized monitor, Plug & Play (VESA DDC) monitor found". Have the Windows colors been set properly?For Windows ME/XP/2000: Set the colors properly at the Control Panel, Display, Settings. Set the video card by referring to the video card manual. Install the monitor driver according to the Driver Installation Instructions. Install the monitor driver according to the Driver Installation Instructions. LED is blinking but no images on the screen. Is the frequency properly adjusted when checking the Display Timing on the menu? Has the video card been set properly?See the video card manual to see if the Plug & Play (VESA DDC) function can be supported. Check the following items if there is trouble with the monitor. Check if the power cord and the cable are properly connected to the computer. Check if the computer beeps more than 3 times when booting. (If it does, request an after-service for the main board of the computer. ) 3. If you installed a new video card or if you assembled the PC, check if the installed the adapter (video) driver and the monitor driver. Check if the scanning ratio of the video screen is set at 75Hz or 85Hz. (Do not exceed 60Hz when using the maximum resolution. ) 5. If you have problems in installing the adapter (video) driver, boot the computer in Safe Mode, remove the Display Adapter at the "Control Panel, System, Device Administrator" and then reboot the computer to reinstall the adapter (video) driver. Tips for Highlight Zone 1. To protect CDT against the screen brightness, the Highlight Zone function persists for three hours and then automatically stops. Once the Highlight Zone has been switched off, you can't select any of the other menus within the Hightlight Zone. When the Highlight Zone function is operated, the surrounding brightness of screen may become dark. Depending on the video card you use, a color saturation phenomenon may occur in the Highlight Zone. In this case, slightly lower the contrast of the Highlight Zone and the color saturation will be reduced. Note: If problems repeatedly occur, contact an authorized service center. Question How can I change the frequency? Check List Answer Frequency can be changed by reconfiguring the video card. [. . . ] Important parameters are luminance, contrast, resolution, reflectance, colour rendition and image stability. Energy Energy-saving mode after a certain time-beneficial both for the user and the environment Electrical safety Emissions Electromagnetic fields Noise emissions Ecology The product must be prepared for recycling and the manufacturer must have a certified environmental management system such as EMAS or ISO 14 000 Restrictions on o chlorinated and brominated flame retardants and polymers o heavy metals such as cadmium, mercury and lead. The requirements included in this label have been developed by TCO Development in cooperation with scientists, experts, users as well as manufacturers all over the world. Since the end of the 1980s TCO has been involved in influencing the development of IT equipment in a more userfriendly direction. [. . . ]