User manual SAMSUNG SYNCMASTER 955MB

[. . . ] SyncMaster 955MB Main > Index Main Page On-Screen Display General Highlight Zone Safety Instructions Notational Power Installation Cleaning Other Troubleshooting Check List Q&A Self-Test Feature Check Introduction Unpacking Front Rear Bottom Specifications General Specifications Preset Timing Modes PowerSaver Setup Connecting Your Monitor Installing the Monitor Driver Automatic Manual Base Installation Information Service Terms Regulatory Natural Color Authority Main > Safety Instructions > Notational Notational Power Installation Clean Other Failure to follow directions noted by this symbol could result in bodily harm or damage to equipment. Prohibited Important to read and understand at all times Do not disassemble Disconnect the plug from the outlet Do not touch Grounding to prevent an electric shock Main > Safety Instructions > Power When not used for extended periods of time, set your PC to DPMS. If using a screen saver, set it to the active screen mode. Notational ? Power Installation Clean Other If the size of your monitor is small, or if the same image is present for long periods of time, you may see afterimages due to damage to the fluorescent substance on the inside of the CDT. Do not use a damaged or loose plug. ? This may cause an electric shock or fire. Do not pull the plug out by the wire nor touch the plug with wet hands. ? This may cause an electric shock or fire. Use only a properly grounded plug and receptacle. ? An improper ground may cause electric shock or equipment damage. Do not excessively bend the plug and wire nor place heavy objects upon them, which could cause damage. ? Failure to do so may cause an electric shock or fire. Disconnect the plug from the outlet during storms or lightening or if it is not used for a long period of time. ? Failure to do so may cause an electric shock or fire. Do not connect too many extension cords or plugs to an outlet. ? This may cause a fire. Main > Safety Instructions > Installation Do not cover the vents on the monitor cabinet. ? Bad ventilation may cause a breakdown or fire. Notational Power Installation Clean Other Put your monitor in a location with low humidity and a minimum of dust. ? An electric shock or fire could result inside the monitor. Do not drop the monitor when moving it. ? This may cause damage to the product or human body. Place the monitor on a flat and stable surface. ? The monitor can cause injury by falling. Set down the monitor carefully. ? It could be damaged or broken. Do not place the monitor face down. ? The CDT surface may be damaged. Do not use the monitor without the monitor stand. ?? It could break down or cause a fire due to bad ventilation. If the monitor must be used without the supplied stand, take steps to insure proper ventilation. Main > Safety Instructions > Clean When cleaning the monitor case or the surface of the CDT, wipe with a slightly moistened, soft fabric. [. . . ] The monitor automatically returns to normal operation when you move the computer's mouse or press a key on the keyboard. For energy conservation, turn your monitor OFF when it is not needed, or when leaving it unattended for long periods. The PowerSaver system operates with a VESA DPMS compliant video card installed in your computer. Use a software utility installed on your computer to set up this feature. State Power Indicator Power Consumption Normal Operation Green 100W(Nominal) 110W(Maximum) Power-off Mode EPA/ENERGY 2000 Green, Blinking Less than 2. 0W This monitor is EPA ENERGY STAR® compliant and ENERGY2000 compliant when used with a computer equipped with VESA DPMS functionality. As an ENERGY STAR® Partner, SAMSUNG has determined that this product meets the ENERGY STAR® guidelines for energy efficiency. Main > Specifications > Preset Timing Modes If the signal transferred from the computer is the same as the following Preset Timing Modes, the screen will be adjusted automatically. However, if the signal differs, the screen may go blank while the power LED is on. Refer to the video card manual and adjust the screen as follows. General PowerSaver Table 1. Preset Timing Modes Display Mode IBM, 640 x 480 IBM, 720 x 400 VESA, 640 x 480 VESA, 640 x 480 VESA, 800 x 600 VESA, 1024 x 768 VESA, 1024 x 768 VESA, 1280 x 1024 Horizontal Frequency (kHz) 31. 469 31. 469 37. 500 43. 269 53. 674 60. 023 68. 677 79. 976 Vertical Frequency (Hz) 59. 940 70. 087 75. 000 85. 008 85. 061 75. 029 84. 997 75. 025 Pixel Clock (MHz) 25. 175 28. 322 31. 500 36. 000 56. 250 78. 750 94. 500 135. 00 Sync Polarity (H/V) -/-/+ -/-/+/+ +/+ +/+ +/+ Preset Timing Modes Horizontal Frequency The time to scan one line connecting the right edge to the left edge of the screen horizontally is called Horizontal Cycle and the inverse number of the Horizontal Cycle is called Horizontal Frequency. Unit: kHz Vertical Frequency Like a fluorescent lamp, the screen has to repeat the same image many times per second to display an image to the user. The frequency of this repetition is called Vertical Frequency or Refresh Rate. Unit: Hz Main > Information > Service Service Terms Regulatory Natural Color Authority U. S. A. : Samsung Computer Products Customer Service 400 Valley Road, Suite 201, Mt. : (973)601-6000, 1-800-SAMSUNG (1-800-726-7864) Fax. : (973)601-6001 http://www. samsungusa. com/monitor/ BRAZIL : Samsung Eletronica da Amazonia Ltda. Manoelito de Ornellas, 303, Terro B Chacara Sto. Antonio, CEP : 04719-040 Sao Paulo, SP SAC : 0800 124 421 http://www. samsung. com. br/ CANADA : Samsung Electronics Canada Inc. 7037 Financial Drive Mississauga, Ontario L5N 6R3 Tel. : (905) 542-1199 http://www. samsung. ca/ COLOMBIA : Samsung Electronics Colombia Cra 9 No 99A-02 Of. 106 Bogota, Colombia Tel. : 9-800-112-112 Fax: (571) 618 - 2068 http://www. samsung-latin. com/ e-mail : soporte@samsung-latin. com PANAMA : Samsung Electronics Latinoamerica( Z. L. ) S. A. Calle 50 Edificio Plaza Credicorp, Planta Baja Panama Tel. : (507) 210-1122, 210-1133 Tel : 800-3278(FAST) http://www. samsung-latin. com/ PERU Servicio Integral Samsung Av. Argentina 1790 Lima1. [. . . ] Some of the features of the TCO'03 Display requirements: Ergonomics · Good visual ergonomics and image quality in order to improve the working environment for the user and to reduce sight and strain problems. Important parameters are luminance, contrast, resolution, reflectance, colour rendition and image stability. Energy-saving mode after a certain time ­ beneficial both for the user and the environment Electrical safety Electromagnetic fields Noise emissions The product must be prepared for recycling and the manufacturer must have a certified environmental management system such as EMAS or ISO 14 000 Restrictions on o chlorinated and brominated flame retardants and polymers o heavy metals such as cadmium, mercury and lead. Energy · · · · · Emissions Ecology · The requirements included in this label have been developed by TCO Development in cooperation with scientists, experts, users as well as manufacturers all over the world. Since the end of the 1980s TCO has been involved in influencing the development of IT equipment in a more user-friendly direction. [. . . ]