User manual SAMSUNG SYNCMASTER 957MB

[. . . ] SyncMaster 757MB/957MB Main > Index Main Page On-Screen Display General Highlight Zone Highlight Zone II MouScreenTM Safety Instructions Notational Power Installation Cleaning Other Troubleshooting Check List Q&A Self-Test Feature Check Introduction Unpacking Front Rear Bottom Specifications General Specifications Preset Timing Modes PowerSaver Setup Connecting Your Monitor Installing the Monitor Driver Automatic Manual Base Installation Information Service Terms Regulatory Natural Color MouScreenTM Authority Notational Power Installation Clean Other Failure to follow directions noted by this symbol could result in bodily harm or damage to equipment. Prohibited Important to read and understand at all times Do not disassemble Disconnect the plug from the outlet Do not touch Grounding to prevent an electric shock When not used for extended periods of time, set your PC to DPMS. If using a screen saver, set it to the active screen mode. Notational Power Installation Clean Other If the size of your monitor is small, or if the same image is present for long periods of time, you may see afterimages due to damage to the fluorescent substance on the inside of the CDT. Do not use a damaged or loose plug. This may cause an electric shock or fire. Do not pull the plug out by the wire nor touch the plug with wet hands. This may cause an electric shock or fire. Use only a properly grounded plug and receptacle. [. . . ] If the mouse is dragged to the right, they are curved to the right. Fine Tuning : When the mouse pointer is correctly placed over the Corner Pin Balance icon, the icon color changes. Then, click the left mouse button, and its fine tuning sub-menu appears in the bottom left corner of the screen. When the mouse cursor is correctly placed over either of the left or right arrows, the arrow color changes, as it does when an icon is selected. Then, click the left mouse button to achieve the desired fine tuning. Holding the mouse button down will cause the value to change rapidly. User's Guide 54 On-Screen Display On-Screen Display Degauss This setting removes blurs on the screen, caused by interference from magnetic fields. Selection and Adjustment : Place and click the mouse pointer on the Degauss icon that is located in the center of the screen. The picture image may become fuzzy for three to five seconds, with the monitor making a ticking sound when the icon is selected. Any fuzzy screen blotches are removed while the magnetic field affecting the screen is degaussed. User's Guide 55 On-Screen Display On-Screen Display 1. Reset This setting cancels adjustments made using the current tab. However, please note that a Reset function is not provided for the Highlight Zone tabs because their nature does not require being reset. 2. Save This setting saves all the adjustments made in the current session since the program was started. 3. OK This closes the monitor setting, saves the current adjustments and exits the program. 4. Cancel This returns the monitor settings to their original state before the current adjustments are saved and exits the program. SyncMaster 957MB On-Screen Display 1. Highlight button : The Highlight Zone ensures clear images on TVs, video conferencing systems or photos by emphasizing a certain area on the screen. Exit/MagicBright button : Use this button to exit or to activate the MagicBright menu. Adjust buttons : These buttons allow you to highlight and adjust items in the menu. Menu button : Use this button to open the OSD and activate a highlighted menu item. On-Screen Display Menu How to adjust MagicBright MagicBright refers to a new monitor feature that offers screen display quality twice as bright and clear than that of existing monitors. It provides display brightness and resolution most appropriate for viewing text, Internet or multimedia animations to satisfy varying user requirements. The user may easily select one of three pre-configured brightness and resolution options by simply pressing one of the MagicBright control buttons located on the monitorís front. Push the MagicBright button again and select the desired mode. When Text is selected, the monitor turns on normal brightness identical to that of existing monitors, which is suitable for reading or working with text. [. . . ] Enter D:\color\eng\setup. exe and then press the key. (If the drive where the CD is inserted is not D:\, enter the applicable drive. ) How to delete the Natural Color software program Select [Setting]/[Control Panel] on the [Start] menu and then double-click [Add/Delete a program]. Select Natural Color from the list and then click the [Add/Delete] button. English > Main > Information > MouScreen TM MouScreenTM S/W MouScreen Program requires built-in USB for use with SyncMaster Products. (Note: SyncMaster 1200NF does not support MouScreen. ) MouScreen is a software program that controls your monitor settings using the USB (Universal Serial Bus) interface. [. . . ]