User manual SAMSUNG AHR18MEB

[. . . ] 8 Users of this product are cautioned not to attempt repairs. Instead, they are requested to directly contact a designated service center or the outlet at which the product was purchased. 9 Do not use an extension cord with this product. 10 The appliance is not intended for use by young children without supervision ; young children should be supervised to ensure that they do not play with the appliance. [. . . ] Please take the time to read them as they will help you take full advantage of the unit's features. N The illustration on page 4 shows the air conditioning unit; it indicates the location and purpose of the main parts and controls on the unit. N In the main part of the document, you will find a series of step-by-step procedures for each function available. The illustrations in the step-by-step procedures use four different symbols: PRESS PUSH IMPORTANT NOTE E-5 Heating Your Room You must select the HEAT mode if you wish to higher the temperature in your room. You can also set the fan speed. 1 Select the operating mode and fan speed. High fan speed Low fan speed Result: Set the operating mode selection dial to. . . HI HEAT LOW HEAT N The air conditioner starts up in Heat mode. N The fan starts up at the speed selected. You can change modes at any time. 2 To adjust the temperature, turn the temperature control dial 27°C ~ 23°C to the red position. (Left side) Result: The air conditioner is started heating, if room temperautre is lower than selected temperature. 27°C ~ 29°C 23°C ~ 18°C 3 To control the direction of the air flow, refer to page 9. E-6 Airing Your Room If the atmosphere in your room is stale, you can air it using the Fan feature and if necessary, evacuate the stale air outside. 1 If you wish to evacuate stale air outside, push the ventilation lever on the front of the unit to the right and the open position ( ). Result: The air inside the room circulates and stale air is evacuated outside. OFF Otherwise, push the ventilation lever to the left and the closed position ( Result: The air simply circulates inside the room. ). HI FAN 2 Set the operating mode selection dial to the FAN position. Result: Note: N The air conditioner starts up in Fan mode. N The left, right " (FAN)" have it's same function. 3 To control the direction of the air flow, refer to page 9. Switching the Air Conditioner Off You can switch the air conditioner off whenever you want. 1 To switch the unit off, simply set the operating mode selection dial to the OFF position. Result: The air conditioner stops operating. E-7 Adjusting the Air Flow Direction Horizontally Depending on the position of the unit in your room, you can adjust the orientation of the inner air flow blades on the right-hand side of the unit, thus increasing the efficiency of the air conditioner. Set the air flow blade swing switch to the ON position. Result: The inner blades swing automatically left and right. To stop the blades moving left and right, set the air flow blade swing switch to the OFF position. To stop the blades in a specific position and orient the air flow in the corresponding direction, simply set the switch to the OFF position when the blades are in the desired position. Adjusting the Air Flow Direction Vertically Again depending on the position of the unit in your room, you can adjust the orientation of the outer air flow blades on the right-hand side of the unit. Upwards. Adjust the air flow blades to the desired position, by pushing them upwards or downwards. If you orient the air flow blades downwards and the unit operates in Cool mode for long periods of time, dew may: N Form on the surface of the blades N Drip from the blades E-8 Operating Recommendation Here are a few recommendations that you should follow when using your air conditioner. Topic Recommendation The air conditioner circulates warm air to heat your room; as a result, some time will be required after starting the air conditioner to warm the entire room. If necessary, set the air conditioner going a short time before you wish to use the room. If a power failure occurs when the air conditioner is operating, the unit is switched off. [. . . ] N Dust may be blocking the air filter; refer to page 10 for cleaning instructions. N Check that there is no obstacle blocking the air flow into or out of the unit. The air flow direction does not change when you set the air flow blade swing switch to the ON position Odours are permeated in the room during air conditioning N Check that the air conditioner has been switched on; if necessary, turn the operating mode selection dial. N Air the room. Technical Specifications Design and specifications are subject to change without notice. Model AHR18MEB AHR24MEB Power Supply 220-240V~, 50Hz E-11 Method of Installation Before installation, be sure to check the installation area for the air conditioner, and installation method of the drain hose. Checkpoints prior to installation 1 Check the cabinet and front grille of the unit for any harmful defects such as scratches. - Refer to the specifications on the label attached to the unit. [. . . ]