User manual SAMSUNG AHT18PGHEA

[. . . ] AHT18PGHBA_E_17335 04/2/23 10:38 Page 23 OWNER'S INSTRUCTIONS AHT18PGHBA AHT18PGHEA AHT24PGHBA AHT24PGHEA Window-type Room Air Conditioner ( Cool and Heater ) E A DB98-17335A(1) AHT18PGHBA_E_17335 04/2/23 10:38 Page 2 Safety Precautions The following safety precautions must be taken when using your air conditioner. · Disconnect all remote electric power supplies before servicing, installing or cleaning. · This must be done by the manufacturer or its service agent or a similar qualified person in order to avoid a hazard. x Users of this product are cautioned not to attempt repair of this product at their own discretion. [. . . ] You can also set the fan speed. Remote Control Control Panel 1 If necessary, press the (On/Off) button. x The operating mode indicator (COOL, FAN or HEATER) Result: on the unit comes on. x The air conditioner starts up in the mode selected when the unit was last used. air Theunit conditioner is fitted with a protection mechanism to prevent the from being damaged when it is started immediately after being: x Plugged in x Stopped It will start up automatically after about three minutes. 2 If the HEATER indicator is not lit up on the unit: x Press the button on the remote control or x Press the button on the unit one or more times until the HEATER indicator lights up x The unit beeps each time you press . Result: x The air conditioner starts up in Heater mode. 3 You can change modes at any time. To adjust the temperature, press the or button on the remote control one or more times until the required temperature is displayed. To adjust the temperature, press the or button on the unit one or more times until the required temperature is displayed. Possible temperatures are between 16°C and 30°C inclusive. x Each time you press the temperature buttons: Result: ­ The temperature is adjusted by 1°C and displayed on the control panel ­ The unit beeps x The air conditioner starts heating if the room temperature is lower than the selected temperature. 4 To set the fan speed to. . . x Press the button on the remote control. or x Press the on the unit until the indicator lights up x Press the button on the remote control. or x Press the on the unit until the indicator lights up x Press the button on the remote control. Cooling Heating Adjust the blades to face. . . Downwards. Adjust the air flow blades to the desired position, by pushing them upwards or downwards. If you orient the air flow blades downwards and the unit operates in Cool mode for a long period of time, dew may: x Form on the surface of the blades x Drip from the blades E-11 AHT18PGHBA_E_17335 04/2/23 10:38 Page 12 Setting the On Timer Remote Control Control Panel The On Timer enables you to switch on the air conditioner automatically after a given period of time. You can set the period of time from 1 hour to 24 hours. You can select the On Timer only when the air conditioner is off. 1 Check that the air conditioner has been switched off; if necessary, press the (On/Off) button. 2 Set the required mode by pressing the appropriate button: x , or on the remote control x button on the unit (press it one or more times until the appropriate operating mode indicator lights up) 3 Set the operating time by pressing: x on the remote control. Possible time is between 1 hour and 24 hours inclusive. Result: x The remaining time is displayed and decreased by 1 hour automatically to indicate the remaining time. x The air conditioner switches on automatically when the operating time reaches zero. You can change the setting mode, fan speed, and air flow direction after setting the On Timer. To Cancel the On Timer To cancel the On Timer, press: x on the remote control or on the unit one or more times until " " is displayed. or x (On/Off) button on the remote control or unit. (The air conditioner operates in the mode selected when the unit was last used. ) E-12 AHT18PGHBA_E_17335 04/2/23 10:38 Page 13 Setting the Off Timer The Off Timer enables you to switch off the air conditioner automatically after a given period of time. You can set the period of time from 1 hour to 24 hours. You can select the Off Timer only when the air conditioner is on. Remote Control Control Panel 1 Check that the air conditioner has been switched on; if necessary, press the (On/Off) button. 2 Set the operating time by pressing: x on the remote control or x on the unit one or more times. [. . . ] The room temperature may be too low or too high. Dust may be blocking the air filter; refer to page 16 for cleaning instructions. Check that there is no obstacle blocking the air flow into or out of the unit. Check that the required temperature has been set correctly. [. . . ]