User manual SAMSUNG AQT12S4GE/HAC

[. . . ] OWNER'S INSTRUCTIONS MANUAL DE INSTRUCCIONES MANUEL D'UTILISATION Indoor unit AQT12S4GB AQT12S4GE AQT18S0GBA AQT18S0GEA AQT24S6GBA AQT24S6GEA Outdoor unit UQT12S4GB UQT12S4GE UQT18S0GBA UQT18S0GEA UQT24S6GBA UQT24S6GEA ESPAÑOL FRANÇAIS Split-type Room Air Conditioner (Cool and Heat) Aire acondicionado doméstico sistema Split (Refrigeración y Calefacción) Climatiseur de type Séparé (Refroidissement et Chauffage) E S F A DB98-16558A(1) ENGLISH Safety Precautions The following safety precautions must be taken when using your air conditioner. · Disconnect all remote electric power supplies before servicing, installing or cleaning. · This must be done by the manufacturer or its service agent or a similar qualified person in order to avoid a hazard. Users of this product are cautioned not to attempt repair of this product at their own discretion. [. . . ] 1 If necessary, press the Result: (On/Off) button. The operation indicator on the indoor unit lights up. The air conditioner starts up in the mode selected when the unit was last used. The air conditioner is fitted with a protection mechanism to prevent the unit from being damaged when it is started immediately after being: Plugged in Stopped lt will start up normally after three minutes. button. IMPORTANT 2 Select COOL mode by pressing the Note You can select the Energy saving mode only in the COOL mode. 3 Press the Result: button. The air conditioner runs in the Energy saving mode. The outer air flow blade moves up and down. To stop the Energy saving mode, press the again. 4 To adjust the temperature, press the button one or more times until the required temperature is displayed. Possible temperatures are between 26°C and 30°C inclusive. Note If you want to adjust temperature under 26°C, cancel the Energy saving mode before adjusting the temperature. 5 To select the fan speed, press the the required setting is displayed. button one or more times until 6 To control the direction of the air flow, refer to pages 16 and 17. E-15 Adjusting the Air Flow Direction Vertically Depending on the position of the indoor unit on the wall of your room, you can adjust the position of the outer air flow blade on the bottom of the unit, thus increasing the efficiency of the air conditioner. 1 Press the Result: button one or more times as required. Cooling Heating Adjust the blade to face. . . Downwards. RECOMMENDATION 2 If you want the blade to move up and down automatically when the air conditioner is operating, press the button. Result: The blade move up and down, around the base position set. 3 To stop the blade moving up and down, press the button again. Note If you switch the air conditioner. . . Set to the initial position powered. E-16 Adjusting the Air Flow Direction Horizontally ENGLISH There are two sets of inner air flow blades. Just as the outer air flow blade can be adjusted vertically, the inner blades can be adjusted horizontally. 1 Adjust each set of inner blades to the required position, by pushing or pulling them sideways. E-17 Setting the On Timer The On Timer enables you to switch on the air conditioner automatically after a given period of time. You can set the period of time from 30 minutes to 24 hours. 1 To set the operating time, press the button one or more times until the required time is displayed. Possible time is between 0. 5 hour and 24 hours inclusive. 2 Press the Result: (Set/Cancel) button to complete the setting. The selected mode and the temperature on the display disappear after 10 seconds. The air conditioner will switch on automatically when the counter displayed on the remote control reaches the set time and disappears the On timer setting. 3 To select an operating mode in advance, press the button until the desired mode is displayed at the top of the remote control. Result: The air conditioner will run in the selected mode when it is turned on. To Cancel the On Timer 1 To cancel the On Timer, press the timer setting disappears. [. . . ] Check whether the Timer indicator on the indoor unit is switched on. If so: - Wait until the switch-on time is reached and the air conditioner starts up automatically - Cancel the timer (see pages 18 and 19 for further details) Check that there are no obstacles between you and the indoor unit. Check that you are close enough to the indoor unit (seven meters/ yards or less). Check that you are pointing the remote control at the remote control sensor in the right of the indoor unit. [. . . ]