User manual SAMSUNG AQV18VBCN

[. . . ] Contents PREPARATION Safety Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Name of Each Part . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Remote Control ­ Buttons and Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Inserting the Remote Control Batteries . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] The indoor unit beeps. 2 Press the Result: button to select cool or heat mode. The indoor unit beeps each time you press the The air conditioner runs in cool or heat mode. button. 3 Press the Result: button. The Off timer is blinking on the remote control. 4 To set the Off timer, press the until the required Off time is displayed. Result: buttons once or more times The mode will be automatically stopped in 8 hours if the operation time is not set. You can set the Off timer by pressing the buttons to turn off the mode automatically at the appointed time within a range of 30 minutes to 12 hours. Each time the buttons are pressed, the time is increased by 30 minutes or 1 hour. mode will be stopped at the appointed off time. 5 Press the Result: Note button. In the case of selecting mode or adjusting the extra mode, you should press the time for button within 10 seconds. If you do not press the button within 10 seconds, mode will be canceled automatically. 6 Press the button to adjust the temperature until the desired temperature is displayed. You can set the temperature between 16°C and 30°C. Result: Each time you press the button; - The temperature adjusts by 1°C - The indoor unit beeps E-18 Vivace_Inv_IB_28491A_E_11. 28. indd 18 2007-12-6 13:12:23 Temperature changes in mode To prevent excessive cooling/heating during sleep, the mode automatically modifies the temperature setting in accordance with the time setting. Temperature and air current change mode, according to the three stages; Falling asleep, Sound sleep, and Waking up from and then the air conditioner will automatically turn off when the set time has elapsed. Three stage prevents you from having difficulty sleeping on extremely hot/cold nights. Falling asleep : Eases you into sleep by dropping the temperature. Sound sleep : Relaxes your body and raises your temperature slightly. aking up from W mode : Allows you to wake up to comfortable crisp air making you feel refreshed and energized. · Set the Off timer in mode for more than 5 hours. Sleep may be disturbed if the mode is set for too short or too long a time because the temperature changes are set to an 8-hour cycle. mode is set for less than 4 hours, the operation will stop at the set time. mode is set for over 5 hours, the last hour will run in Waking Up stage before · Recommended set temperature is between 25°C~27°C for cooling and 21°C~23°C for heating. Cool mode Temp. Set temperature When the 8-hour cycle completes, this section repeats. When the 8-hour cycle completes, this section repeats. Set temperature Time(hr. ) To deactivate mode indicator will disappear. 1. Press the Set/Cancel button on the remote control. [. . . ] Check if the circuit breaker is switched off. Check if the air conditioner is cooling only model. Check if the remote control is for cooling only model. Check if set temperature higher(lower) than current temperature. [. . . ]