User manual SAMSUNG AR30FSSSBWKN

[. . . ] Australia_A3050_IB&IM_EN_03979A-00. indd 1 2013-8-21 19:51:06 Features of your new air conditioner 2-step cooling 2-step cooling function will quickly cool the room to reach the desired temperature and then it will adjust the fan speed and air flow direction automatically to help you stay comfortable and refreshing. Fast cooling/heating If you want the strong and cool/warm air, just select Fast function!It will get you the strongest air! Comfort cooling/heating If you want the comfortable and refreshing air, Comfort function will spread the cool/warm air indirectly to you, so that you can stay comfortable. Single User Use Single User function when you are alone at home. Single User function will minimize the energy consumption with inverter technology and reduce your electricity bill by adjusting the maximum operating capacity of the compressor. Easy Filter There is no grille to remove before separating the filter from the air conditioner!Therefore, filter can be cleaned easily, more frequently! [. . . ] When the ice formed in winter or the outdoor temperature is too low, the air conditioner operates in defrost mode automatically. In defrost mode, indoor fan stops and warm air does not come out. • If the doors or windows are open, it may cause bad cooling (heating) performance. • Check if the air conditioner has just been turned on after stopping cooling or heating operation. In this case, just a fan will run to protect the outdoor unit compressor. • Check if the pipe length is too long. When the pipe length exceeds maximum allowable pipe length, cooling (heating) performance may decrease. • Check if you have selected mode. In this mode, you mode is cannot adjust the air flow direction. (If the operating in Heat mode, you can adjust the air flow direction. ) The temperature adjustment is not working. Cool/Warm air does not come out of the air conditioner. Air flow adjustment is not working. English-30 Australia_A3050_IB&IM_EN_03979A-00. indd 30 2013-8-21 19:51:17 PROBLEM Fan speed adjustment is not working. Remote controller is not working. SOLUTION • Check if you have selected Auto/Dry/Fast/ mode. In these mode, fan speed is set to Auto and you cannot adjust the fan speed. • Check if your batteries are depleted. • Make sure nothing is blocking your remote controller sensor. • Check that there are strong lighting apparatus near the air conditioner. Strong light which comes from fluorescent bulbs or neon signs may interrupt the electric waves. • Check if you press the Set/Cancel button on the remote controller after you have set the time. • Press the Power button or disconnect the power plug/switch off the auxiliary power switch. If the indicator is still blinking, contact the service center. • Check if the appliance is running in a smoky area. Ventilate the room or operate the air conditioner in Fan mode for 1~2 hours. [. . . ] Use the product after taking care of the error that occurs. Error indicator LED Display Display LED 1 LED 2 LED 3 SMART SAVER/ WIFI/SPI Error on indoor temperature sensor , Error on indoor heat exchanger Error on indoor fan motor display and all LED blinks , 1. Check if the service valve is open 2. Check for refrigerant leakage (pipe connections, heat exchanger) and charge refrigerant if necessary 3. Check if there's any blockage on refrigerant cycle (indoor unit/outdoor unit) 4. Check if additional refrigerant has been added after pipe extension 1. Check the connection of the connector 1. Check the connection of the connector 1. Check the connection of the connector 2. Remove foreign substance (Check for the cause that restrains motor) 1. Re-set options EEPROM/Option error Error Measures to take by an installer OPERATION TIMER Smart install error (blockage error/ refrigerant leakage)  : Off / : Blinking / : On English-55 Australia_A3050_IB&IM_EN_03979A-00. indd 55 2013-8-21 19:51:25 Final check and trial operation To complete the installation, perform the following checks and tests to ensure that the air conditioner operates correctly. Check the followings: • Strength of the installation site • Tightness of pipe connection to detect gas leak • Electric wiring connection • Heat-resistant insulation of the pipe • Drainage • Grounding conductor connection • Correct operation (follow the steps below) 1. Press the Power button and check the following:  The indicator on the indoor unit lights up.   he airflow blade opens and the fan gears up for operation. T 2. Press the Mode button to select Cool or Heat mode.  In Cool mode, use  In Heat mode, use Temp hr. + or – button and set the temperature at 16 °C. [. . . ]