User manual SAMSUNG AS12SGGE/ROD

[. . . ] O¢H°IETM Indoor unit AS07S8GB AS07S8GE AS07SBGE AS09S8GB AS09S8GE AS09SBGE AS12SBGE AS12SGGB AS12SGGE AS14SGGB AS18S0GB AS18S0GE AS24S6GB AST24S6GE Outdoor unit US07S8GB US07S8GE US07SBGE US09S8GB US09S8GE US09SBGE US12SBGE US12SGGB US12SGGE US14SGGB US18S0GB US18S0GE US24S6GB UST24S6GE Split-type Room Air Conditioner (Cool) Aire acondicionado doméstico sistema Split (Refrigeración) Climatiseur de type Séparé (Refroidissement) Condizionatore d'aria per ambienti ad unità Separate (Raffreddamento) Aparelho de ar condicionado tipo Split (Refrigeração) Geteilte raumklimaanlage (Kühlen) ¢IAIPOYMENO K§IMATITMTIKO ¢øMATIOY(æÍË~) E S F I P D G DB98-08801A(4) E§§HNIKA DEUTSCH PORTUGUÊS ITALIANO FRANÇAIS ESPAÑOL OWNER'S INSTRUCTIONS MANUAL DE INSTRUCCIONES MANUEL D'UTILISATION ISTRUZIONI PER L'USO MANUAL DE INSTRUÇÕES GEBRAUCHSANWEISUNG ENGLISH Safety Precautions WARNING DANGER x If the power supply cord of this air conditioner is damaged, it must be replaced by the manufacturer or its authorized service personnel only in order to avoid a safety hazard. x Do not attempt to install the air conditioner by yourself. x This unit contains no user-serviceable parts. Always consult authorized service personnel for repairs. [. . . ] x The air conditioner starts up in the mode selected when the unit was last used. x The indoor unit beeps. 2 Press the Result: button. x The temperature and fan settings are adjusted automatically. x The air conditioner cools the room as quickly as possible. x After 30 minutes, the air conditioner is reset automatically to the previous mode, temperature and fan settings. But, if you press the button in DRY or FAN mode, it will change to AUTO mode automatically. 3 If you wish to stop the Turbo function before the end of the 30-minute period, press the button one or more times until or disappears. Result: The air conditioner is reset automatically to the previous mode, temperature and fan settings. 4 To control the direction of the air flow, refer to page 15. E-11 Removing Excess Humidity If the atmosphere in your room is very humid or damp, you can remove excess humidity without lowering the room temperature too much. 1 If necessary, press the Result: (On/Off) button. x The operation indicator on the indoor unit lights up. x The air conditioner starts up in the mode selected when the unit was last used. The air conditioner is fitted with a protection mechanism to prevent the unit from being damaged when it is started immediately after being: x Plugged in x Stopped lt will start up normally after three minutes. IMPORTANT 2 Select COOL mode by pressing the Note button. You can select the Energy saving mode only in COOL mode. 3 Press the Result: x x x x button. The air conditioner runs in the Energy saving mode. The outer air flow blade moves up and down. To stop the Energy saving mode, press the again. 4 To adjust the temperature, press the button one or more times until the required temperature is displayed. Possible temperatures are between 26°C and 30°C inclusive. Note If you want to adjust temperature under 26°C, cancel the Energy saving mode before adjusting the temperature. 5 To select the fan speed, press the the required setting is displayed. button one or more times until 6 To control the direction of the air flow, refer to page 15. E-14 Adjusting the Air Flow Direction Vertically ENGLISH Depending on the position of the indoor unit on the wall of your room, you can adjust the position of the outer air flow blade on the bottom of the unit, thus increasing the efficiency of the air conditioner. 1 Press the Result: button one or more times as required. Upwards. RECOMMENDATION 2 If you want the blade to move up and down automatically when the air conditioner is operating, press the button. Result: The blade move up and down, around the base position set. 3 To stop the blade moving up and down, press the button again. Note If you switch the air conditioner. . . Set to the initial position powered. Adjusting the Air Flow Direction Horizontally There are two sets of inner air flow blades. Just as the outer air flow blade can be adjusted vertically, the inner blades can be adjusted horizontally. 1 Adjust each set of inner blades to the required position, by pushing or pulling them sideways. E-15 Setting the On Timer The On Timer enables you to switch on the air conditioner automatically after a given period of time. You can set the period of time from 30 minutes to 24 hours. [. . . ] Problem The air conditioner does not operate at all Explanation/Solution x Check that the breaker used for the air conditioner is switched on. x Check that the operation indicator on the indoor unit is on; if necessary press the (On/Off) button on the remote control. x Check whether the TIMER indicator on the indoor unit is switched on. If so: - Wait until the switch-on time is reached and the air conditioner starts up automatically - Cancel the timer (see pages 16 and 17 for further details) x Check that there are no obstacles between you and the indoor unit. [. . . ]