User manual SAMSUNG AST18S6GDC

[. . . ] OWNER'S INSTRUCTIONS Indoor unit AST18S6GDC AST24S6GEC Outdoor unit UST18S6GDC UST24S6GEC SPLIT-TYPE ROOM AIR CONDITIONER ( Cool ) E DB98-17839A(1) Safety Precautions The following safety precautions must be taken when using your air conditioner. · Disconnect all remote electric power supplies before servicing, installing or cleaning. · This must be done by the manufacturer or its service agent or a similar qualified person in order to avoid a hazard. Users of this product are cautioned not to attempt repair of this product at their own discretion. [. . . ] 1 If necessary, press the Result: (On/Off) button. The air conditioner starts up in Cool mode with Turbo fan speed. The operation indicator on the indoor unit lights up. The indoor unit beeps. 2 Press the Result: button. The temperature and fan settings are adjusted automatically. The air conditioner cools the room as quickly as possible. After 30 minutes, the air conditioner is reset automatically to the previous mode, temperature and fan settings. But, if you press the button in DRY or FAN mode, it will change to AUTO mode automatically. 3 If you wish to stop the Turbo function before the end of the 30-minute period, press the button one or more times until or disappears. Result: The air conditioner is reset automatically to the previous mode, temperature and fan settings. 4 To control the direction of the air flow, refer to page 15. E-11 Removing Excess Humidity If the atmosphere in your room is very humid or damp, you can remove excess humidity without lowering the room temperature too much. 1 If necessary, press the Result: (On/Off) button. The air conditioner starts up in Cool mode with Turbo fan speed. The operation indicator on the indoor unit lights up. IMPORTANT The air conditioner is fitted with a protection mechanism to prevent the unit from being damaged when it is started immediately after being: Plugged in Stopped It will start up normally after three minutes. 2 If the is not displayed at the top of the remote control, press the button on the remote control one or more times until it appears. The indoor unit beeps each time you press the The air conditioner runs in DRY mode. button. Result: Note 3 To adjust the temperature, press the button one or more times until the required temperature is displayed. Possible temperatures are between 18°C and 30°C inclusive. 1 Press the Result: button one or more times as required. Upwards. RECOMMENDATION 2 If you want the blade to move up and down automatically when the air conditioner is operating, press the button. Result: The blade move up and down, around the base position set. 3 To stop the blade moving up and down, press the button again. Note If you switch the air conditioner. . . Set to the initial position powered. Adjusting the Air Flow Direction Horizontally There are two sets of inner air flow blades. Just as the outer air flow blade can be adjusted vertically, the inner blades can be adjusted horizontally. 1 Adjust each set of inner blades to the required position, by pushing or pulling them sideways. E-15 Setting the On Timer The On Timer enables you to switch on the air conditioner automatically after a given period of time. You can set the period of time from 30 minutes to 24 hours. 1 To set the operating time, press the button one or more times until the required time is displayed. Possible time is between 0. 5 hour and 24 hours inclusive. 2 Press the Result: (Set/Cancel) button to complete the setting. The selected mode and the temperature on the display disappear after 10 seconds. [. . . ] The air conditioner starts up in the most suitable mode for the room temperature: Room Temperature 21°C or above Operating Mode Cool 3 To switch the air conditioner off, press the On/Off switch again. Note Even if the air conditioner has been switched on via the On/Off switch, operations can still be controlled using the remote control as usual. E-20 Solving Common Problems Before contacting the after-sales service, perform the following simple checks. They may save you the time and expense of an unnecessary call. Problem The air conditioner does not operate at all Explanation/Solution Check that the breaker used for the air conditioner is switched on. [. . . ]