User manual SAMSUNG AST24P6GED/XBG

[. . . ] OWNER'S INSTRUCTIONS MANUAL DE INSTRUCCIONES MANUEL D'UTILISATION Indoor unit AST18PJGB AST18PJGBS AST18PJGE AST18PJGES AST24P6GBD(S) AST24P6GED(S) Outdoor unit UST18PJGB UST18PJGBS UST18PJGE UST18PJGES UST24P6GBD(S) UST24P6GED(S) ESPAÑOL FRANÇAIS Split-type Room Air Conditioner (Cool) Aire acondicionado doméstico sistema Split (Refrigeración) Climatiseur de type Séparé (Refroidissement) E S F A DB98-20882A(2) ENGLISH Register your product at www. samsung. com/global/register Safety Precautions You should take the following safety precautions when using your air conditioner. · If you don't follow the safety precautions, you may get the risk of an electric shock, injury or death. ·The manufacturer or qualified service personnel must install this air conditioner. · Unplug the electric power before repairing, installing or cleaning. WARNING DURING OPERATION x Do not repair the air conditioner at your discretion. It is recommended to contact a service center directly. [. . . ] But, if you press the button in DRY or FAN mode, it will change to AUTO mode automatically. 2 Press the Result: 3 If you wish to stop the Turbo function before the end of the 30-minute period, press the Result: button again. The air conditioner is reset automatically to the previous mode, temperature and fan settings. 4 To control the direction of the air flow, refer to pages 16 and 17. E-11 Removing Excess Humidity If the atmosphere in your room is very humid or damp, you can remove excess humidity without lowering the room temperature too much. 1 If necessary, press the Result: (On/Off) button. x The air conditioner starts up in Cool mode with Turbo fan speed. x The operation indicator on the indoor unit lights up. The air conditioner is fitted with a protection mechanism to prevent the unit from being damaged when it is started immediately after being: x Plugged in x Stopped It will start up normally after three minutes. IMPORTANT 2 If the is not displayed at the top of the remote control, press the button on the remote control one or more times until it appears. Result: Note x The indoor unit beeps each time you press the x The air conditioner runs in DRY mode. button. 3 To adjust the temperature, press the button one or more times until the required temperature is displayed. Possible temperatures are between 18°C and 30°C inclusive. The outer air flow blade moves up and down. To stop the Energy saving mode, press the button again. 4 To adjust the temperature, press the button one or more times until the required temperature is displayed. Possible temperatures are between 26°C and 30°C inclusive. Note If you want to adjust temperature under 26°C, cancel the Energy saving mode before adjusting the temperature. 5 To select the fan speed, press the until the required setting is displayed. button one or more times 6 To control the direction of the air flow, refer to pages 16 and 17. E-14 Generating Anion ENGLISH The air conditioner can generate anion with an ionizer in the indoor unit. Since it is an additional function, you can select it any mode, even when the air conditioner is turned off. Note If you press the button during off, the air conditioner will turn on automatically and generate anion in the Fan mode with Low fan speed. 2 If you wish to stop the Anion function, press the button again. Result: The air conditioner is reset automatically to the previous mode, temperature and fan settings. 3 To control the direction of the air flow, refer to pages 16 and 17. E-15 Adjusting the Air Flow Direction Vertically Depending on the position of the indoor unit on the wall of your room, you can adjust the position of the outer air flow blade on the bottom of the unit, thus increasing the efficiency of the air conditioner. 1 Press the Result: button one or more times as required. Upwards. RECOMMENDATION 2 If you want the blade to move up and down automatically when the air conditioner is operating, press the Result: button. The blade move up and down, around the base position set. 3 To stop the blade moving up and down, press the button again. Note If you switch the air conditioner. . . Set to the initial position powered. E-16 Adjusting the Air Flow Direction Horizontally ENGLISH There are two sets of inner air flow blades. Just as the outer air flow blade can be adjusted vertically, the inner blades can be adjusted horizontally. 1 Adjust each set of inner blades to the required position, by pushing or pulling them sideways. E-17 Setting the On Timer The On Timer enables you to switch on the air conditioner automatically after a given period of time. You can set the period of time from 30 minutes to 24 hours. [. . . ] x Check that the operation indicator on the indoor unit is on; if necessary press the (On/Off) button on the remote control. x Check whether the Timer indicator on the indoor unit is switched on. If so: - Wait until the switch-on time is reached and the air conditioner starts up automatically - Cancel the timer (see pages 18 and 19 for further details) x Check that there are no obstacles between you and the indoor unit. x Check that you are close enough to the indoor unit (seven meters/yards or less). [. . . ]