User manual SAMSUNG AST24S6GEC

[. . . ] OWNER'S INSTRUCTIONS MANUAL DE INSTRUCCIONES MANUEL D'UTILISATION Indoor unit AST12S4GB AST12S4GE AST18S0GBA AST18S0GEA AST24S6GBA AST24S6GEA Outdoor unit UST12S4GB UST12S4GE UST18S0GBA UST18S0GEA UST24S6GBA UST24S6GEA ESPAÑOL FRANÇAIS Split-type Room Air Conditioner (Cool) Aire acondicionado doméstico sistema Split (Refrigeración) Climatiseur de type Séparé (Refroidissement) E S F A DB98-16559A(1) ENGLISH Safety Precautions The following safety precautions must be taken when using your air conditioner. · Disconnect all remote electric power supplies before servicing, installing or cleaning. · This must be done by the manufacturer or its service agent or a similar qualified person in order to avoid a hazard. Users of this product are cautioned not to attempt repair of this product at their own discretion. [. . . ] The temperature and fan settings are adjusted automatically. The air conditioner cools the room as quickly as possible. After 30 minutes, the air conditioner is reset automatically to the previous mode, temperature and fan settings. But, if you press the button in DRY or FAN mode, it will change to AUTO mode automatically. 3 If you wish to stop the Turbo function before the end of the 30-minute period, press the button one or more times until or disappears. Result: The air conditioner is reset automatically to the previous mode, temperature and fan settings. 4 To control the direction of the air flow, refer to page 15. Removing Excess Humidity If the atmosphere in your room is very humid or damp, you can remove excess humidity without lowering the room temperature too much. 1 If necessary, press the Result: (On/Off) button. The air conditioner starts up in Cool mode with Turbo fan speed. The operation indicator on the indoor unit lights up. IMPORTANT The air conditioner is fitted with a protection mechanism to prevent the unit from being damaged when it is started immediately after being: Plugged in Stopped It will start up normally after three minutes. 2 If the is not displayed at the top of the remote control, press the button on the remote control one or more times until it appears. The air conditioner runs in the Energy saving mode. The outer air flow blade moves up and down. To stop the Energy saving mode, press the again. 4 To adjust the temperature, press the button one or more times until the required temperature is displayed. Possible temperatures are between 26°C and 30°C inclusive. Note If you want to adjust temperature under 26°C, cancel the Energy saving mode before adjusting the temperature. 5 To select the fan speed, press the the required setting is displayed. button one or more times until 6 To control the direction of the air flow, refer to page 15. E-14 Adjusting the Air Flow Direction Vertically ENGLISH Depending on the position of the indoor unit on the wall of your room, you can adjust the position of the outer air flow blade on the bottom of the unit, thus increasing the efficiency of the air conditioner. 1 Press the Result: button one or more times as required. Upwards. RECOMMENDATION 2 If you want the blade to move up and down automatically when the air conditioner is operating, press the button. Result: The blade move up and down, around the base position set. 3 To stop the blade moving up and down, press the button again. Note If you switch the air conditioner. . . Set to the initial position powered. Adjusting the Air Flow Direction Horizontally There are two sets of inner air flow blades. Just as the outer air flow blade can be adjusted vertically, the inner blades can be adjusted horizontally. 1 Adjust each set of inner blades to the required position, by pushing or pulling them sideways. E-15 Setting the On Timer The On Timer enables you to switch on the air conditioner automatically after a given period of time. You can set the period of time from 30 minutes to 24 hours. 1 To set the operating time, press the button one or more times until the required time is displayed. Possible time is between 0. 5 hour and 24 hours inclusive. 2 Press the Result: (Set/Cancel) button to complete the setting. The selected mode and the temperature on the display disappear after 10 seconds. [. . . ] They may save you the time and expense of an unnecessary call. Problem The air conditioner does not operate at all Explanation/Solution Check that the breaker used for the air conditioner is switched on. Check that the operation indicator on the indoor unit is on; if necessary press the (On/Off) button on the remote control. Check whether the Timer indicator on the indoor unit is switched on. [. . . ]