User manual SAMSUNG AW09F0SEA

[. . . ] Should this happen, switch off the breaker used for your air conditioner and contact your installation specialist. Make sure that the unit is correctly ventilated at all times: Do not place clothing or other materials over it. If the wireless remote control will not be used for a long time, remove the batteries. [. . . ] 11 x METHOD OF INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 E-3 Air Conditioning Unit - Main Parts and Control Panel The design and shape are subject to change, depending on the model. Inner air flow blades (right/left orientation) Air inlet(Inside) Air filter(Inside) Air inlet (Outside) Ventilation lever Outer air flow blades (up/down orientation) Power Cable BLUE BROWN YELLOW/GREEN Main Power Earth Power cable connection should be committed to an installation engineer. Cooling lamp Operating mode selection dial Temperature control dial Air flow blade swing switch E-4 Getting Started You have just purchased a window-type room air conditioner and it has been installed by your installation specialist. Your Owner's Instructions contain much valuable information on using your air conditioner. Please take the time to read them as they will help you take full advantage of the unit's features. x The illustration on page 4 shows the air conditioning unit; it indicates the location and purpose of the main parts and controls on the unit. x In the main part of the document, you will find a series of step-by-step procedures for each function available. The illustrations in the step-by-step procedures use four different symbols: PRESS PUSH IMPORTANT NOTE E-5 Cooling Your Room You must select the Cool mode if you wish to lower the temperature in your room. You can also set the fan speed. 1 Select the operating mode and fan speed. High fan speed Mid fan speed Low fan speed Result: Set the operating mode selection dial to. . . HI COOL MID COOL LOW COOL x The air conditioner starts up in Cool mode. x The fan starts up at the speed selected. 27°C ~ 23°C You can change modes at any time. 2 To adjust the temperature, turn the temperature control dial to the desired position. Possible temperatures: Between 18°C and 29°C inclusive. 27°C ~ 29C 23°C ~ 18°C Result: The air conditioner is started cooling as turn on the cooling lamp, if room temperature is higher than selected temperature. 3 To control the direction of the air flow, refer to page 8. E-6 Airing Your Room If the atmosphere in your room is stale, you can air it using the Fan feature and if necessary, evacuate the stale air outside. 1 If you wish to evacuate stale air outside, push the ventilation lever on the front of the unit to the right and the open position ( ). Result: The air inside the room circulates and stale air is evacuated outside. ). Otherwise, push the ventilation lever to the left and the closed position ( Result: The air simply circulates inside the room. 2 Set the operating mode selection dial to the HI FAN, MID FAN or LOW FAN position. Result: HI FAN : The fan turns high speed. The air conditioner starts up in Fan mode. 3 To control the direction of the air flow, refer to page 8. Switching the Air Conditioner Off You can switch the air conditioner off whenever you want. 1 To switch the unit off, simply set the operating mode selection dial to the OFF position. Result: The air conditioner stops operating. E-7 Adjusting the Air Flow Direction Horizontally Depending on the position of the unit in your room, you can adjust the orientation of the inner air flow blades on the right-hand side of the unit, thus increasing the efficiency of the air conditioner. 1 Set the air flow blade swing switch to the ON position. Result: The inner blades swing automatically left and right. 2 To stop the blades moving left and right, set the air flow blade swing switch to the OFF position. To stop the blades in a specific position and orient the air flow in the corresponding direction, simply set the switch to the OFF position when the blades are in the desired position. Adjusting the Air Flow Direction Vertically Again depending on the position of the unit in your room, you can adjust the orientation of the outer air flow blades on the right-hand side of the unit. Upwards. Adjust the air flow blades to the desired position, by pushing them upwards or downwards. If you orient the air flow blades downwards and the unit operates in Cool mode for long periods of time, dew may: x Form on the surface of the blades x Drip from the blades E-8 Operating Recommendation Here is a recommendations that you should follow when using your air conditioner. [. . . ] The air conditioner does not cool x Check that the correct operating mode has been selected. Example: High storage 1 Open the front grille. Safety clip CAUTION Removal and Reassembly of the Front Grille For user's safety, a safety clip has been installed in the front grille. 1 Grasp the lower part of the front grille and the air filter handle, then open the grille. 2 Remove the safety clip and the front grille. [. . . ]