User manual SAMSUNG AW1005B

[. . . ] Should this happen, switch off the breaker used for your air conditioner and contact your installation specialist. Make sure that the unit is correctly ventilated at all times: Do not place clothing or other materials over it. If the wireless remote control will not be used for a long time, remove the batteries. (If applicable) When using a wireless remote control, the distance should not be more than 7 meters from the air conditioner. [. . . ] Batteries may be completely discharged after 12 months, even if they have not actually been used. Push the battery cover on the rear of the remote control with your thumb in the direction of the arrow and remove it. Insert the two batteries, taking care to respect the polarities : + on the battery with + on the remote control. - on the battery with - on the remote control. Close the cover by sliding it back until it clicks into place. 1 2 3 E-7 Cooling Your Room You must select the Cool mode if you wish to lower the temperature in your room. You can also set the Fan speed. Remote Control Control Panel 1 Press the (On/Off) button. Result: The air conditioner starts up in the Cool mode. The unit beeps twice. The air conditioner is fitted with a protection mechanism to prevent the unit from being damaged when it is started immediately after being: Plugged in Stopped It will start up normally after three minutes. 2 If the temperature is not displayed on the control panel: Press the button on the remote control or Press the button on the unit one or more times until the temperature is displayed. Result: The unit beeps each time you press the / button. The air conditioner starts up in the Cool mode. You can change modes at any time. 3 To adjust the temperature, press the or buttons on the remote control or unit one or more times until the desired temperature is displayed. The temperature can be set between 64°F and 86°F. Result: Each time you press the or buttons: ­ The temperature is adjusted by 1°F and displayed on the control panel ­ The unit beeps The air conditioner starts cooling, if the room temperature is higher than the selected temperature. If the room temperature reaches the set temperature, the air conditioner stops cooling, but the fan is still operating. 4 To set the fan speed: Press the , or button on the remote control as desired. or Press the button on the unit one or more times until the desired Fan speed(F1, F2 or F3) is displayed. Fan Speed 5 To control the direction of the air flow, refer to page 11. E-8 Airing Your Room If you want to provide air circulation without cooling, you can use the Fan mode. 1 If necessary, press the Result: (On/Off) button. Remote Control Control Panel The air conditioner starts up in the Cool mode. The unit beeps twice. 2 If the fan speed(F1, F2 or F3) is not displayed on the control panel: Press the button on the remote control or Press the button on the unit one or more times until the fan speed (F1, F2 or F3) is displayed. Result: The unit beeps each time you press the / button. The air conditioner starts up in Fan mode. Mode Cool/Dry/Fan Mode Cool/Dry/Fan You can change modes at any time. When the air conditioner is in the Fan mode, the temperature cannot be set or displayed. 3 To set the fan speed: Press the , or button on the remote control as desired. or Press the button on the unit one or more times until the desired fan speed(F1, F2 or F3) is displayed. Fan Speed 4 To control the direction of the air flow, refer to page 11. E-9 Removing Excess Humidity If the atmosphere in your room is very humid or damp, you can remove excess humidity without lowering the room temperature too much. Remote Control Control Panel 1 If necessary, press the Result: (On/Off) button. The air conditioner starts up in the Cool mode. The unit beeps. The air conditioner is fitted with a protection mechanism to prevent the unit from being damaged when it is started immediately after being: Plugged in Stopped It will start up normally after three minutes. 2 If the temperature is not displayed on the control panel: Press the button on the remote control or Press the button on the unit one or more times until the temperature is displayed. Result: The unit beeps each time you press the / button. [. . . ] Check that there are no obstacles between you and the unit. Replace the remote control batteries if necessary. Check that you are close enough to the unit (seven metres/yards or less). Check that you are pointing the remote control at the remote control sensor on the unit. [. . . ]