User manual SAMSUNG AW109DB/XAC

[. . . ] Should this happen, switch off the breaker used for your air conditioner and contact your installation specialist. Make sure that the unit is correctly ventilated at all times: Do not place clothing or other materials over it. If the wireless remote control will not be used for a long time, remove the batteries. (If applicable) When using a wireless remote control, the distance should not be more than 7 meters from the air conditioner. [. . . ] The air conditioner starts up in the Cool mode. The unit beeps twice. The air conditioner is fitted with a protection mechanism to prevent the unit from being damaged when it is started immediately after being: Plugged in Stopped It will begin to cool after three minutes. 2 If the temperature is not displayed on the control panel: button on the remote control Press the or Press the button on the unit one or more times until Result: The unit beeps each time you press the / The air conditioner starts up in the Cool mode. You can change modes at any time. is displayed. button. 3 To adjust the temperature, press the or buttons on the remote control or unit one or more times until the desired temperature is displayed. The temperature can be set between 18 C and 30 C. Result: Each time you press the or buttons: - The temperature is adjusted by 1 C and displayed on the control panel - The unit beeps The air conditioner starts cooling, if the room temperature is higher than the selected temperature. If the room temperature reaches the set temperature, the air conditioner stops cooling, but the fan is still operating. 4 To set the fan speed: , or button on the remote control as desired. Press the or Press the button on the unit one or more times until the desired Fan speed(F1, F2 or F3) is displayed. 5 To control the direction of the air flow, refer to page 11. E-8 Airing Your Room If you want to provide air circulation without cooling, you can use the Fan mode. 1 If necessary, press the Result: (On/Off) button. Remote Control Control Panel The air conditioner starts up in the Cool mode. The unit beeps twice. 2 If the fan speed(F1, F2 or F3) is not displayed on the control panel: button on the remote control Press the or Press the button on the unit one or more times until the fan speed (F1, F2 or F3) is displayed. Result: The unit beeps each time you press the / button. The air conditioner starts up in Fan mode. When the air conditioner is in the Fan mode, the temperature cannot be set or displayed. 3 To set the fan speed: Press the , or button on the remote control as desired. or Press the button on the unit one or more times until the desired fan speed(F1, F2 or F3) is displayed. 4 To control the direction of the air flow, refer to page 11. E-9 Removing Excess Humidity If the atmosphere in your room is very humid or damp, you can remove excess humidity without lowering the room temperature too much. Remote Control Control Panel 1 If necessary, press the Result: (On/Off) button. The air conditioner starts up in the Cool mode. The air conditioner is fitted with a protection mechanism to prevent the unit from being damaged when it is started immediately after being: Plugged in Stopped It will begin to cool after three minutes. 2 If the temperature is not displayed at the top of the control panel, press button on the control panel one or more times until it the appears. Result: The unit beeps each time you press the The air conditioner runs in Dry mode. button. 3 To adjust the temperature, press the or buttons one or more times until the required temperature is displayed. Possible temperatures are between 18 C and 30 C inclusive. Result: Each time you press the or buttons: - The temperature is adjusted by 1 C - The unit beeps The air conditioner starts removing the excess humidity; the quantity of air is adjusted automatically. 4 To control the direction of the air flow, refer to page 11. E-10 Adjusting the Air Flow Direction Horizontally Depending on the position of the unit in your room, you can adjust the orientation of the inner air flow blades on the unit. Adjust the air flow blades to the desired position by pushing them side to side. Adjusting the Air Flow Direction Vertically The outer air flow blades can be adjusted to control the vertical air flow direction. Upwards. Adjust the air flow blades to the desired position, by pushing them upwards or downwards. If you orient the air flow blades downwards and the unit operates in Cool mode for long periods of time, dew may: - Form on the surface of the blades - Drip from the blades E-11 Setting the On Timer The On Timer enables you to switch on the air conditioner automatically after a given time. You can select the On timer only when the air conditioner is off. Remote Control Control Panel 1 Check that the air conditioner has been switched off; if necessary, (On/Off) button. [. . . ] Labor 1 Year (In home) Parts 1 Year Limited 5-Years Compressor Warranty Within one year of purchase Samsung Electronics Canada Inc. will provide a replacement compressor if it is found to be defective in material or workmanship. During the existing four years (second through fifth year) Samsung Electronics Canada Inc. will provide a replacement only, without charge, if it is found to be defective in material or workmanship. [. . . ]