User manual SAMSUNG AW126JB

[. . . ] CAUTION The manufacturer do not take the responsibility of the accident happened because the air conditioner is not fixed firmly or installed securely, during installing or using the product. In case you have difficulty in installation, you must ask for an installation specialist help. The accident will be happened in case of installing improperly. E-2 Contents x PREPARING YOUR AIR CONDITIONER s s s s s Safety Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Air Conditioning Unit - Main Parts, Buttons and Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Result: x Each time you press the temperature buttons: ­ The temperature is adjusted by 1°C and displayed on the control panel ­ The unit beeps x The air conditioner starts cooling if the room temperature is higher than the selected temperature. 4 To set the fan speed to. . . Press the Press the button on the remote control. button on the remote control. Each time you press a button, the unit beeps. 5 To control the direction of the air flow, refer to page 10. E-8 Airing Your Room ENGLISH If the atmosphere in your room is stale, you can air it using the Fan feature and if necessary, evacuate the stale air outside. 1 If you wish to evacuate stale air outside, push the ventilation lever on the front of the unit to the right and the open position ( ). The air inside the room circulates and stale air is evacuated Result: outside. Otherwise, push the ventilation lever to the left and the closed position ( ). The air simply circulates inside the room. Result: 2 If necessary, press the (On/Off) button. x The operating mode indicator (COOL or FAN) on the Result: unit comes on. x The air conditioner starts up in the mode selected when the unit was last used. x The unit beeps twice. Remote Control Control Panel 3 If the FAN indicator is not lit up on the unit: x Press the FAN button on the remote control or x Press the POWER/MODE button on the unit one or more times until the FAN indicator lights up Result: x The unit beeps each time you press POWER/MODE. x The air conditioner starts up in Fan mode. When the air conditioner is in Fan mode, the temperature is not displayed; moreover, you do not need to set the temperature. Press the Press the button on the remote control. button on the remote control. x x 4 To set the fan speed to. . . High Low Result: Each time you press a button, the unit beeps. 5 To control the direction of the air flow, refer to page 10. E-9 Adjusting the Air Flow Direction Horizontally Depending on the position of the unit in your room, you can adjust the orientation of the inner air flow blades on the right-hand side of the unit, thus increasing the efficiency of the air conditioner. Remote Control 1 Press the Result: button on the remote control. The inner blades swing automatically left and right. button again. 2 To stop the blades moving left and right, press the To stop the blades in a specific position and orient the air flow in the corresponding direction, simply press the button when the blades are in the desired position. Adjusting the Air Flow Direction Vertically Again depending on the position of the unit in your room, you can adjust the orientation of the outer air flow blades on the right-hand side of the unit. Upwards. Adjust the air flow blades to the desired position, by pushing them upwards or downwards. If you orient the air flow blades downwards and the unit operates in Cool mode for a long period of time, dew may: x Form on the surface of the blades x Drip from the blades E-10 Switching the Unit Off Automatically (Off Timer) ENGLISH You can set the timer to switch the air conditioner off automatically at a given time. Example: You wish to switch the unit off two hours after you have gone to bed. Remote Control 1 If necessary, press the (On/Off) button. Control Panel 2 Select the required mode by pressing the appropriate button: x COOL or FAN on the remote control x POWER/MODE button on the unit (press it one or more times until the appropriate operating mode indicator lights up) 3 Set the operating time by pressing: x TIMER v or w on the remote control one or more times. Example: To switch the unit off two hours after you have gone to bed, set the operating time to 2 hours. Possible operating times are between 1 and 24 hours inclusive. [. . . ] Remove the screw located at the lower section of the front grille. It is secured in the section depending on the model. 3-1 Press both sides of the cabinet in the direction of the arrow as shown in the figure. 3-2 Pull the lower part of the front panel slightly forward. [. . . ]