User manual SAMSUNG AW12FCDBC/XAP

[. . . ] Air Conditioning Unit - Main Parts, Buttons and Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Remote Control Buttons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Getting Started . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Inserting the Remote Control Batteries . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 4 5 6 7 x OPERATING YOUR AIR CONDITIONER s s s s Cooling Your Room . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Result: x The air conditioner starts up in Cool mode. 3 You can change modes at any time. To adjust the temperature, press the Temperature button on the remote control one or more times until the required temperature is displayed. To adjust the temperature, press the Temperature button on the unit one or more times until the required temperature is displayed. Possible temperatures are between 18°C and 30°C . x Each time you press the temperature buttons: Result: ­ The temperature is adjusted by 1°C and displayed on the control panel ­ The unit beeps x The air conditioner starts cooling if the room temperature is higher than the selected temperature. 4 To set the fan speed x Press the HIGH, MED or LOW button on the remote control it depends of your requirement or Press the Fan speed button on the unit until fan speed appears on the indicator (F1, F2, F3) Result: Each time you press a button, the unit beeps 5 To control the direction of the air flow, refer to page 10. E-8 Airing Your Room If you wish to provide ventilation, you can use the Fan feature. Remote Control Control Panel 1 If necessary, press the (On/Off) button. x Result: x The air conditioner starts up in the mode selected when the unit was last used. x The unit beeps twice. 2 If the FAN speed(F1, F2, F3) indicator is not lit up on the unit: x Press the FAN button on the remote control or x Press the MODE button on the unit one or more times until the FAN indicator lights up (F1, F2, F3) Result: x The unit beeps each time you press MODE. x The air conditioner starts up in Fan mode. x When the air conditioner is in Fan mode, the temperature is not displayed; in this case, you do not need to set the temperature. 3 To set the fan speed x Press the HIGH, MED or LOW button on the remote control it depends of your requirement. or Press the Fan speed button on the unit until fan speed appears on the indicator (F1, F2, F3) Result: Each time you press a button, the unit beeps. 4 4 To control the direction of the air flow, refer to page 10. E-9 Adjusting the Air Flow Direction Vertically Again depending on the position of the unit in your room, you can adjust the orientation of the outer air flow blades on the right-hand side of the unit. RECOMMENDATION When. . . Upwards. Adjust the air flow blades to the desired position, by pushing them upwards or downwards. If you orient the air flow blades downwards and the unit operates in Cool mode for a long period of time, dew may: x Form on the surface of the blades x Drip from the blades E-10 Setting the On timer The On Timer enables you to switch on the air conditioner automatically after a given period time. You can select the On timer only when the air conditioner is off. Remote Control Control Panel 1 Check that the air conditioner has been switched off; if necessary, press the (On/Off) button. 2 Set the operating time by pressing: x x Timer on the remote control. Possible time is between 1 hour and 12 hour inclusive. Result: x The remaining time is displayed and decreased by 1 hour automatically to indicate the remaining time. x The air conditioner switches on automatically when the operating time reaches zero. You can change the setting mode, fan speed after setting the On timer. To Cancel the On Timer To cancel the timer, press: x Timer on the remote control or unit one or more times until "--" is displayed. or x on the remote control or unit (The air conditioner operates in the mode selected when the unit was last used. ) E-11 Setting the Off Timer Remote Control Control Panel The Off Timer enables you to switch off the air conditioner automatically after a given period of time. You can set the period of time from 1 hour to 12 hours. You can select the Off timer only when the air conditioner is on. 1 Check that the air conditioner has been switched on; if necessary, press the (On/Off) button. 2 Set the operating time by pressing: x Timer on the remote control or x Timer on the unit one or more times. Possible times are between 1 hour and 12 hour inclusive. Result: x The remaining time is displayed and decreased by 1 hour automatically to indicate the remaining time. Remove all dust on the air filter with a vaccum cleaner or brush. When you have finished, insert the air filter back into its original position. 3 4 5 The air conditioner has two or three grille grooves depending of the model. . Wipe the surface of the unit with a neutral detergent and then wipe it again with dry cloth. [. . . ] Example: High storage 1 2 3 Open the front grille ; refer to page 14. Remove the screw located at the lower section of the front grille. It is secured in the section depending on the model. 3-1 Press both sides of the cabinet in the direction of the arrow as shown in the figure. [. . . ]