User manual SAMSUNG AW12P0BC

[. . . ] Make sure that the unit is correctly ventilated at all times: Do not place clothing or other materials over it. If the wireless remote control will not be used for a long time, remove the batteries. (If applicable) When using a wireless remote control, the distance should not be more than 7 meters from the air conditioner. (If applicable) The air conditioner must be plugged into its own specific power source, which must be installed in compliance with national wiring, earthing and safety regulations. [. . . ] Adjusting the Air Flow Direction Vertically . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Temperature and Humidity Ranges . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Cleaning Your Air Conditioner. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Solving Common Problems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 5 6 6 7 7 7 8 9 0 OPERATION YOUR AIR CONDITIONER n n n n n RECOMMENDATIONS FOR USE n n n INSTALLATION. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . The illustrations in the step-by-step procedures use four different symbols: PRESS CAUTION NOTE PUSH IMPORTANT "The high inrush current of the starting compressor motor can have adverse effects to the operation of other equipment under unfavorable mains conditions. This equipment does not comply with the relevant technical standards for the limitation of voltage fluctuations and flicker. " Before connection this equipment to the power supply system, please report to your suply authority and obtain the consent. Do not connect other electric appliances to the same supply lines. E-3 Air Conditioning Unit - Main Parts and Control Panel The design and shape are subject to change according to the model. Air Outlet Inner air flow blades (right/left orientation) Air inlet (Inside) The air filter is located in side Outer air flow blades (up/down orientation) Air inlet (Outside) Ventilation lever Power Cable The type of the power plug may differ according to the type of local power supply. Power plug Operating mode selection dial Temperature control dial Coolest Coolest E-4 Cooling Your Room You must select the Cool mode if you wish to lower the temperature in your room. You can also set the fan speed. Select the operating mode and fan speed. High fan speed Between HIGH and LOW Low fan speed Result: Set the operating mode selection dial to. . . HI COOL MED COOL LOW COOL The air conditioner starts up in the Cool mode. The fan starts up at the speed selected. You can change modes at any time. To adjust the temperature, turn the temperature control dial to the desired position. Possible temperatures: Between 8 °C and 9 °C inclusive. Result: The air conditioner starts cooling if the room temperature is higher than the selected temperature. 3 To control the direction of the air flow, refer to page 7. E-5 Airing Your Room If the atmosphere in your room is stale, you can air it using the Fan feature and if necessary, evacuate the stale air outside. If you wish to evacuate stale air outside, push the ventilation lever on the front of the unit to the right and the open position ( Result: ). The air inside the room circulates and stale air is evacuated outside. ). Otherwise, push the ventilation lever to the left and the closed position ( Result: The air simply circulates inside the room. Set the operating mode selection dial to the HI FAN or LOW FAN position. Result: The air conditioner starts up in Fan mode. 3 To control the direction of the air flow, refer to page 7. Switching the Air Conditioner Off You can switch the air conditioner off whenever you want. To switch the unit off, simply set the operating mode selection dial to the OFF position. Result: The air conditioner stops operating. E-6 Adjusting the Air Flow Direction Horizontally Depending on the position of the unit in your room, you can adjust the orientation of the inner air flow blades on the unit, thus increasing the efficiency of the air conditioner. Adjust the air flow blades to the desired position by sliding them side to side. Adjusting the Air Flow Direction Vertically Again depending on the position of the unit in your room, you can adjust the orientation of the outer air flow blades on the right-hand side of the unit. RECOMMENDATION When. . . Upwards. Adjust the air flow blades to the desired position, by pushing them upwards or downwards. If you orient the air flow blades downwards and the unit operates in Cool mode for long periods of time, dew may: From on the surface of the blades Drip from the blades Temperature and Humidity Ranges The following table indicates the temperature and humidity ranges within which the air conditioner can be used in the best condition . Mode Cooling IndoorTemperature °C to 3°C approx. OutdoorTemperature °C to 43°C approx. Indoor Humidity 80% or less If the air conditioner is used at. . . Higher temperatures Lower temperatures Higher humidity levels Then. . . The automatic protection feature may be triggered and the air conditioner stopped. A water leakage or some other malfunction may happen if the heat exchanger freezes. Water way condense on and drip from the surface of the unit if it is used for long periods. E-7 Cleaning Your Air Conditioner Be sure to clean the air filter periodically to maintain the air conditioner in the best condition for a long period of time. [. . . ] Dust may be blocking the air filter; refer to page 8 cleaning instructions. Check that there is no obstacle blocking the air flow into or out of the unit. Odours are permeated in the room during air conditioning Air the room. E-9 Installation (for 60Hz) Electrical Requirements For personal safety: This appliance must be properly grounded. Do not, under any circumstances, cut or remove the third grounding prong from the power cord. [. . . ]