User manual SAMSUNG AWT18QBHDDDXTL

[. . . ] OWNER'S INSTRUCTIONS AWT18QBHDA MODEL CODE: AWT17QBHD***/XTL AWT18QBHD***/XTL Window-type Room Air Conditioner (Cool) E DB98-15151A(1) Safety Precautions The following safety precautions must be taken when using your air conditioner. 1 The unit must be plugged into an independent circuit. The air conditioner must be installed in accordance with national wiring regulations and safety regulations wherever applicable. 2 Some installation locations may require installation of a short circuit breaker or grounding. 3 If the supply cord is damaged, it must be replaced by a special cord or assembly available from the manufacturer or its service agent. [. . . ] 1 If you wish to discharge stale air, push the ventilation lever on the front of the unit to the right and open position ( Result: ). The air inside the room circulates and stale air is discharged outside. ). Otherwise, push the ventilation lever to the left and closed position ( Result: The air simply circulates inside the room. 2 If necessary, press the Result: (On/Off) button. Remote Control Control Panel The air conditioner starts up in the cool mode(Fan speed will not be changed). The unit beeps twice. 3 If the fan speed(F1, F2 or F3) is not displayed on the control panel: Press the button on the remote control or Press the button on the unit one or more times until the fan speed (F1, F2 or F3) is displayed. Result: The unit beeps each time you press the / button. The air conditioner starts up in Fan mode. You can change modes at any time. When the air conditioner is in the Fan mode, the temperature cannot be set or displayed. 4 To set the fan speed: Press the , or button on the remote control as desired. or Press the button on the unit one or more times until the desired fan speed(F1, F2 or F3) is displayed. Low Medium High 5 To control the direction of the air flow, refer to pages 10 and 11. E-9 Adjusting the Air Flow Direction Horizontally Depending on the position of the unit in your room, you can adjust the orientation of the inner air flow blades on the right-hand side of the unit, thus increasing the efficiency of the air conditioner. Remote Control Control Panel 1 Press the button on the remote control or button on the unit. Result: The inner blades swing automatically left and right. In the Energy Saving mode, the blades may stop when the compressor is off. For details on the Energy Saving mode, refer to page 15. 2 To stop the blades moving left and right, press the again. / button To stop the blades in a specific position and orient the air flow in the corresponding direction, simply press the / button when the blades are in the desired position. E-10 Adjusting the Air Flow Direction Vertically The outer air flow blades can be adjusted to control the vertical air flow direction. RECOMMENDATION When. . . Upwards. Adjust the air flow blades to the desired position, by pushing them upwards or downwards. If you orient the air flow blades downwards and the unit operates in the Cool mode for long periods of time, dew may: Form on the surface of the blades Drip from the blades E-11 Setting the On Timer The On Timer enables you to switch on the air conditioner automatically after a given time. You can select the On timer only when the air conditioner is off. You can select the On timer only when the air conditioner operates in the Cool mode. Remote Control Control Panel 1 Check that the air conditioner has been switched off; if necessary, press the (On/Off) button. 2 Set the operating time by pressing the button on the remote control or button on the unit one or more times until the desired time is displayed. The operating time can be set between 1 and 24 hours. Result: Each time you press the button: ­ The time is adjusted by 1 hour and displayed on the control panel ­ The unit beeps The operating time is displayed and decreases automatically to indicate the remaining time. The air conditioner starts up in the Cool mode automatically when the operating time reaches zero. You can select the fan speed, temperature, air flow direction and Energy saving mode after setting the On timer and Off timer mode. However, when you change the mode, the On timer and Off timer mode is canceled. To Cancel the On Timer To cancel the timer, press: Timer on the remote control or unit one or more times until "--" is displayed. or The (On/Off) button on the remote control or unit. (The air conditioner operates in the cool mode. ) E-12 Setting the Off Timer The Off Timer enables you to switch off the air conditioner automatically after a given time. You can select the Off timer only when the air conditioner is on. [. . . ] Replace the remote control batteries if necessary. Check that the correct operating mode has been selected(Cool). Dust may be blocking the air filter; refer to page 17 for cleaning instructions. Check that there is no obstacle blocking the air flow into or out of the unit. The air conditioner does not operate with the remote control No beep is heard when you press the (On/Off) button on the remote control The air conditioner does not cool The timer is not correctly triggered Odour is permeating the room during air conditioning Check that the timer has been programmed correctly; refer to pages 12~14. Ventilate the room. E-18 Technical Specifications Design and specifications are subject to change without notice. [. . . ]