User manual SAMSUNG AWT18SBWDCG

[. . . ] OWNER'S INSTRUCTIONS AWT18SBWDC Window-type Room Air Conditioner (Cool) E DB98-09660A(1) Safety Precautions The following safety precautions must be taken when installing and using your air conditioner. 1 The air conditioner must be plugged into its own specific power source, which must be installed in compliance with national wiring, earthing and safety regulations. Depending on national regulations and your specific installation, you may need to install: A circuit breaker For further information on electrical requirements, contact a professional electrician. This device must be installed according to the national electrical rules. 2 Make sure that the unit is correctly ventilated at all times; do NOT place clothing or other materials over it. 3 NEVER spill liquids of any kind into the unit. Should this happen, unplug the unit and contact your installation specialist. 4 Do NOT insert anything between the air outlet blades, as it may damage the inner fan and you may be hurt. [. . . ] The operating mode indicator (COOL or FAN) on the Result: unit comes on. The air conditioner starts up in the mode selected when the unit was last used. The unit beeps twice. Control Panel 3 If the FAN indicator is not lit up on the unit: Press the button on the remote control or Press the MODE button on the unit one or more times until the FAN indicator lights up Result: The unit beeps each time you press MODE. The air conditioner starts up in Fan mode. When the air conditioner is in Fan mode, the temperature is not displayed; in this case, you do not need to set the temperature. Press the button on the remote control. or Press the on the unit until the indicator lights up Press the button on the remote control. or Press the on the unit until the indicator lights up Press the button on the remote control. or Press the on the unit until the indicator lights up Each time you press a button, the unit beeps. E-9 4 To set the fan speed to. . . High Med Low Result: 5 To control the direction of the air flow, refer to page 10. Adjusting the Air Flow Direction Horizontally Remote Control Control Panel Depending on the position of the unit in your room, you can adjust the orientation of the inner air flow blades on the right-hand side of the unit, thus increasing the efficiency of the air conditioner. 1 Press the Result: (or on the unit) button on the remote control. The inner blades swing automatically left and right. 2 To stop the blades moving left and right, press the button on the remote control. (or on the unit) To stop the blades in a specific position and orient the air flow in the (or on the unit) corresponding direction, simply press the button on the remote control when the blades are in the desired position. Adjusting the Air Flow Direction Vertically Again depending on the position of the unit in your room, you can adjust the orientation of the outer air flow blades on the right-hand side of the unit. Upwards. Adjust the air flow blades to the desired position, by pushing them upwards or downwards. If you orient the air flow blades downwards and the unit operates in Cool mode for a long period of time, dew may: Form on the surface of the blades Drip from the blades E-10 Setting the On timer The On Timer enables you to switch on the air conditioner automatically after a given period time. You can set the period of time from 1 hour to 24 hours. You can select the On timer only when the air conditioner is off. Remote Control Control Panel 1 Check that the air conditioner has been switched off; if necessary, press the (On/Off) button. 2 Set the required mode by pressing the appropriate button: or on the remote control Mode button on the unit (press it one or more times until the appropriate operating mode indicator lights up) 3 Set the operating time by pressing: Timer on the remote control. Make sure that you have selected either COOL mode. Press the or Press the Result: button on the remote control button on the unit. Each time you press a button, the unit beeps. The "SLEEP" passes through the control panel for about 15 seconds and the " " will be displayed. The remaining time is displayed and decreased by 1 hour automatically to indicate the remaining time. The air conditioner will be controlled as illustration below. Remote Control Control Panel Cooling When the temperature has been increased by 1°C (after 1 hour), it is maintained for 7 hours. To Cancel the Sleep Timer To cancel the timer, press: on the remote control. The SLEEP indicator is no longer displayed. The air conditioner operates in the mode selected last. If you select the Energy Saving mode in the Sleep Timer mode, the Sleep Timer will be cancelled and the air conditioner will start up in the Energy Saving mode. E-13 Selecting Energy Saving mode Remote Control Control Panel 1 If you wish to save energy when using your air conditioner, select the energy saving mode with the Energy Saver button. [. . . ] Check that you are close enough to the unit (seven metres/yards or less). Check that you are pointing the remote control at the remote control sensor on the unit. Replace the remote control batteries if necessary. Check that the correct operating mode has been selected COOL. [. . . ]