User manual SAMSUNG AWT24WHB

[. . . ] USER'S MANUAL AWT18YM Series AWT24YM Series AWT18WM Series AWT24WM Series AWT18WH Series AWT24WH Series Window-type Room Air Conditioner (Cooling) E A DB98-28078A-6 Register your product at www. samsung. com/register Safety Precautions The following safety precautions must be taken when using your air conditioner. WARNING DURING OPERATION u Risk of electric shock. · Disconnect all remote electric power supplies before servicing, installing or cleaning. · This must be done by the manufacturer or its service agent or a similar qualified person in order to avoid a hazard. Users of this product are cautioned not to attempt repair of this product at their own discretion. Instead, they are requested to directly contact a designated service center or the outlet at which the product was purchased. [. . . ] 3 To adjust the temperature, press the or button on the remote control one or more times until the required temperature is displayed. To adjust the temperature, press the or button on the unit one or more times until the required temperature is displayed. Possible temperatures are between 8°C and 30°C inclusive. Result: Each time you press the temperaure buttons. - The temperature is adjusted by °C and displayed on the control panel - The unit beeps The air conditioner starts cooling if the room temperature is higher than the selected temperature. 4 To set the fan speed to. . . Press the or Press the button on the unit one or more times until the the desired fan speed(F, F, or F3) is displayed. : Low Speed : Med Speed : High Speed , or button on the remote control as desired 5 To control the direction of the air flow, refer to page . E-8 Airing Your Room If the atmosphere in your room is stale, you can air it using the Fan feature and if necessary, evacuate the stale air outside. If you wish to evacuate stale air outside, push the ventilation lever on the front of the unit to the right and the open position ( Result: ). The air inside the room circulates and stale air is evacuated outside. Otherwise, push the ventilation lever to the left and the closed position ( Result: The air simply circulates inside the room. (On/Off) button. ). If necessary, press the Result: Remote Control Control Panel The air conditioner starts up in the Cool mode. The unit beeps twice. 3 If the FAN indicator is not lit up on the unit: Press the or Press the button on the unit one or more times until the FAN indicator lights up Result: The unit beeps each time you press the The air conditioner starts up in Fan mode. button on the remote control You can change modes at any time. When the air conditioner is in the Fan mode, the temperature is not displayed; in this case, you do not need to set the temperature. 4 To set the fan speed to. . . button on the remote control as desired Press the button on the unit one or more times until the the desired fan speed(F, F, or F3) is displayed. : Low Speed : Med Speed : High Speed 5 To control the direction of the air flow, refer to page . E-9 Removing Excess Humidity If the atmosphere in your room is very humid or damp, you can remove excess humidity without lowering the room temperature too much. If necessary, press the Result: (On/Off) button. Remote Control Control Panel The air conditioner starts up in the Cool mode. The unit beeps. The air conditioner is fitted with a protection mechanism to prevent the unit from being damaged when it is started immediately after being. Plugged in Stopped It will begin to cool after three minutes If the dry indicator is not displayed at the top of the control panel, press the button on the control panel one or more times until it appears. You can select the On Timer only when the air conditioner is off. Check that the air conditioner has been switched off; if necessary, press the (On/Off) button. Remote Control Control Panel Set the operating time by pressing: on the remote control. or on the unit one or more times. Possible time is between hour and 4 hours inclusive. Result: The remaining time is displayed and decreased by hour automatically to indicate the remaining time. The air conditioner switches on automatically when the operating time reaches zero. You can change the setting mode, fan speed, and air flow direction after setting the On Timer. To Cancel the On Timer To cancel the On Timer, press: " or on the remote control or " is displayed. on the unit one or more times until (On/Off) button on the remote control or unit. [. . . ] (Be sure not to use benzene, solvent or other chemical products). If you. . . Will not be using the air conditioner for a long period of time Then. . . Set the fan going for three to four hours to dry the inside of the air conditioner thoroughly. Switch the air conditioner off and unplug it from the wall socket. [. . . ]