User manual SAMSUNG AZ09A7KE

[. . . ] Window-type Room Air Conditioner ( Cool and Heat ) Climatiseur de type Fenêtre ( Refroidissement et Chauffage ) E F A DB98-05458A(1) FRANÇAIS AZ09F7KE AZ09A7KE AZ09F8KE AZ09A8KE ENGLISH OWNER'S INSTRUCTIONS MANUEL D'UTILISATION Safety Precautions The following safety precautions must be taken when installing and using your air conditioner. 1 The air conditioner must be plugged into its own specific power source, which must be installed in compliance with national wiring, earthing and safety regulations. Depending on national regulations and your specific installation, you may need to install: x A circuit breaker For further information on electrical requirements, contact a professional electrician. This device must be installed according to the national electrical rules. 2 Make sure that the unit is correctly ventilated at all times; do NOT place clothing or other materials over it. 3 NEVER spill liquids of any kind into the unit. Should this happen, unplug the unit and contact your installation specialist. 4 Do NOT insert anything between the air outlet blades, as it may damage the inner fan and you may be hurt. [. . . ] Once the correct temperature has been reached, the fan is automatically set to the required speed. 5 To control the direction of the air flow, refer to page 11. E-9 Airing Your Room If the atmosphere in your room is stale, you can air it using the Fan feature and if necessary, evacuate the stale air outside. 1 Hr. C FAN SPEED If you wish to evacuate stale air outside, pull the ventilation lever on the front of the unit and the open position ( ). Result: The air inside the room circulates and stale air is evacuated outside. ). Otherwise, push the ventilation lever and the closed position ( Result: Open Position Closed Position The air simply circulates inside the room. Remote Control Control Panel 2 If necessary, press the Result: (On/Off) button. POWER x The operating mode indicator (COOL, HEAT, or FAN) on the unit comes on. x The air conditioner starts up in the mode selected when the unit was last used. x The unit beeps twice. 3 RESTART COOL FAN If the FAN indicator is not lit up on the unit: x Press the button on the remote control or x Press the MODE button on the unit one or more times until the FAN indicator lights up Result: x The unit beeps each time you press MODE. x The air conditioner starts up in Fan mode. When the air conditioner is in Fan mode, the temperature is not displayed; in this case, you do not need to set the temperature. Press the Press the button on the remote control. C Set the operating time by pressing: x TIMER v or w on the remote control one or more times. Example: To switch the unit off two hours after you have gone to bed, set the operating time to 2 hours. Possible operating times are between 1 and 24 hours inclusive. Result: x The Hr indicator flashes for about ten seconds. x The operating time is displayed and decreased automatically to indicate the remaining time. x The air conditioner switches off automatically when the operating time reaches zero. You can change your setting at any time. Canceling the Off Timer If you no longer wish to use the Off Timer that you have set, you can cancel it at any time. Remote Control Control Panel To cancel the timer, press: x TIMER v or w on the remote control one or more times until "- -" is displayed. Result: x The unit beeps each time you press a button. x The Hr indicator on the unit switches off. x The air conditioner operates automatically. Hr. C E-12 Operating Recommendation ENGLISH Here are a few recommendations that you should follow when using your air conditioner. Topic Heating performances Recommendation The heat pump inside the air conditioner absorbs heat from outside air and brings it indoors. If the temperature of the outside air drops, the air conditioner will heat less. If you find that the room is not warm enough, use an additional heating appliance. The air conditioner circulates warm air to heat your room; as a result, some time will be required after starting the air conditioner to warm the entire room. [. . . ] x Check that the correct operating mode has been selected COOL or HEAT. x The room temperature may be too low or too high. x Dust may be blocking the air filter; refer to page 15 or 16 for cleaning instructions. x Check that there is no obstacle blocking the air flow into or out of the unit. When heating, the required room x Check that the required temperature has been set correctly. temperature is never reached and x Increase the fan speed. [. . . ]