User manual SAMSUNG AZ09F1KE

[. . . ] If the power cord is damaged in any way, it must be replaced by an approved power cord available from the manufacturer or its service agent. 6 Do NOT attempt to repair the unit yourself. If it is damaged in any way, contact: x An approved service center x The outlet at which the air conditioner was purchased 7 Do NOT place any obstacles in front of the unit. 8 The appliance is not intended for use by young children or infirm person without supervision; young children should be supervised to ensure that they do not play with the appliance. CAUTION The manufacturer do not take the responsibility of the accident happened because the air conditioner is not fixed firmly or installed securely, during installing or using the product. [. . . ] x The fan starts up at the speed selected. You can change modes at any time. 2 To adjust the temperature, turn the temperature control dial towards the left and the red position. Possible temperatures: Between 25°C and 29°C inclusive. Result: The air conditioner starts heating if the room temperature is lower than the selected temperature. 29°C ~ 27°C 27°C ~ 23°C 23°C ~ 18°C 3 To control the direction of the air flow, refer to page 9. E-7 Airing Your Room If the atmosphere in your room is stale, you can air it using the Fan feature and if necessary, evacuate the stale air outside. 1 If you wish to evacuate stale air outside, pull the ventilation lever on the front of the unit and the open position ( Result: ). The air inside the room circulates and stale air is evacuated outside. ). Otherwise, push the ventilation lever and the closed position ( Result: The air simply circulates inside the room. Open Position Closed Position 2 Set the operating mode selection dial to the FAN position. Both fan settings (left and right) have the same function. The air conditioner starts up in Fan mode. Result: 3 To control the direction of the air flow, refer to page 9. Switching the Air Conditioner Off You can switch the air conditioner off whenever you want. To switch the unit off, simply set the operating mode selection dial to the OFF position. Result: The air conditioner stops operating. E-8 Adjusting the Air Flow Direction Horizontally Depending on the position of the unit in your room, you can adjust the orientation of the inner air flow blades on the right-hand side of the unit, thus increasing the efficiency of the air conditioner. 1 Set the air flow blade swing switch to the Result: position . The inner blades swing automatically left and right. The blades may stop swinging momentarily when the Deice function is activated (see page 10 for further details on this function). They will start swinging again automatically as soon as the Deice function stops. 2 To stop the blades moving left and right, set the air flow blade swing switch to the position. To stop the blades in a specific position and orient the air flow in the corresponding direction, simply set the switch to the position when the blades are in the required position. Adjusting the Air Flow Direction Vertically Again depending on the position of the unit in your room, you can adjust the orientation of the outer air flow blades on the right-hand side of the unit. Cooling Heating Adjust the blades to face. . . Downwards. Adjust the air flow blades to the required position, by pushing them upwards or downwards. If you orient the air flow blades downwards and the unit operates in Cool mode for a long period of time, dew may: x Form on the surface of the blades x Drip from the blades E-9 Operating Recommendations Here are a few recommendations that you should follow when using your air conditioner. Topic Recommendation Heating The heat pump inside the air conditioner absorbs heat from performances outside air and brings it indoors. If the temperature of the outside air drops, the air conditioner will heat less. If you find that the room is not warm enough, use an additional heating appliance. Warm air circulation The air conditioner circulates warm air to heat your room; as a result, some time will be required after starting the air conditioner to warm the entire room. If necessary, set the air conditioner going a short time before you wish to use the room. When outside temperatures are low and humidity is high, frost may form in the unit's condenser when heating with your air conditioner. If this happens: x The unit stops heating x The air flow blades stop swinging x The Deice mode is triggered automatically for about five minutes. No intervention is required from you; after about five minutes, the air conditioner starts operating again normally. High indoor and outdoor temperatures Power failure If both the indoor and outdoor temperatures are high and you select the Heat mode, the fan and compressor in the unit may stop at times. This is normal; simply wait until the air conditioner switches on again. [. . . ] Remove the screw located at the lower section of the front grille. It is secured in the section depending on the model. 3-1 Press both sides of the cabinet in the direction of the arrow as shown in the figure. 3-2 Pull the lower part of the front panel slightly forward. [. . . ]