User manual SAMSUNG BF641FB

[. . . ] If your oven needs repair, contact a SAMSUNG Service Centre or your dealer. If the supply cord is defective, it must be replaced by a special cord or assembly available from the manufacturer or an authorised service agent. Electrical leads and cables should not be allowed to touch the oven. The oven should be connected to the mains power supply by means of an approved circuit breaker or fuse. [. . . ] Ensure protection from live parts when installing the oven. The kitchen cabinet in which the oven is built in must satisfy stability requirements as specified in DIN 68930. Technical Specifications Input voltage / frequency Volume (usable capacity) Output rating Net weight Weight with packaging Housing (W x H x D) Oven interior (W x H x D) 230 V ~ 50 Hz 65 L max. 38 kg 595 x 595 x 566 mm 440 x 365 x 405 mm Power Connection If the appliance is not connected to the mains with a plug, a multi-pole isolator switch (with at least 3 mm contact spacing) must be provided in order to satisfy safety regulations. The power cable (H05 RR-F or H05 VV-F, min. 1. 5 m, 1. 5 ~ 2. 5 mm²) must be of sufficient length to be connected to the oven, even if the oven stands on the floor in front of its built-in cabinet. Open the rear connection cover of the oven with a screwdriver and loosen the screws of the cable clamp before you connect the power lines to the relevant connection terminals. The oven is earthed via the ( )-terminal. If the oven is connected to the mains with a plug, this plug must remain accessible after the oven is installed. Samsung will take no responsibility for accidents that originate from a missing or faulty earth connection. Installation in the Cabinet This is a built-in oven, which needs to be installed into an upper or lower cabinet. After installation, remove the vinyl protective film from the door to the appliance and the protective film from the interior surfaces of the oven. min. 560 Lower Cabinet 4 Parts and Features Oven controls 2 EN 1 4 3 1. Time Select Knob Front design The front panel is available in various material and color options including stainless steel, white, black and glass. For purposes of quality improvement, the appearance may be subject to change. Accessory BAKING TRAY The baking tray could be used for the preparation of cakes, cookies and other pastries. BIG GRID The big grid should be used for grilling and roasting meals. You could use it with casseroles and other baking pots. Be sure to attach the accessory correctly to the racks. Trays need to have at least 2 cm space towards the bottom of the oven, otherwise the enamel surface could be damaged. Be very carefull removing meals and/or accessories out of the oven. Hot meals, accessories and surfaces can burn you! 5 Settings EN Time setting If the oven is pluged to the power suply for the first time, its display will illuminate for short time and after 3 seconds 12:00 starts to blink. Before the oven can be used the time setting must be completed. 1 Press Time Select Knob, hour figures blink. 2 Turn Time Select Knob, set desired time in hours. 3 Press Time Select Knob, minute figures blink. 4 Turn Time Select Knob, set desired time in minutes. 5 Press Time Select Knob to confirm. Set Timer 1 Turn Time Select Knob, set timer time. While the timer is operating, the " " mark on the left side of the screen rotates to indicate the process. If you want to stop the timer operation, set the timer to 0:00. While it is operating, press the Time selection knob to display the clock for the current time. 2 Press Time Select Knob to confirm. 6 Oven Use Using the Fast Preheating( ) mode EN If you use the FAST PREHEATING option, you can increase the temperature up to the set value in no time. This will drastically shorten your waiting time until the preheating is done. Use the FAST PREHEATING option to increase the temperature to the set value until the preheating is completed. [. . . ] Call your local service centre. What should I do if the time display is blinking? There was a power failure. Set the clock (see section "Time setting"). What should I do if the oven light doesn't illuminate? The oven light is faulty. Replace the oven light bulb (see section "Bulb Exchange"). What should I do if the oven's fan is running without having been set? Following use, the oven's fan runs until the oven has cooled down. Call your local service centre if the fan continues to run after the oven has cooled down. Error and Safety codes Error and Safety codes General Functions An error of the oven may cause low performance and problems in safety. [. . . ]