User manual SAMSUNG CB-14Y4T

[. . . ] COLOUR TELEVISION Owner's Instructions Before operating the unit, please read this manual thoroughly, and retain it for future reference. REMOTE CONTROL MENU CONTROL TELETEXT FUNCTION ENG S afety Instructions The following illustrations represent the precautions to be taken when using and moving your television. 10% 35° 75% H 5° H Do NOT expose the television to extreme temperature conditions (below 5°C and above 35°C) or to extreme humidity conditions (less than 10% and more than 75%). Do NOT expose the television to direct sunlight. Do NOT expose the television to any liquids. If the television is broken, do not try to repair it yourself. Contact qualified service personnel. During a storm conditions (especially when there is lightning) unplug the television from the mains socket and aerial. If the remote control is not used for a long period of time, remove the batteries and store it in a cool, dry place. NEVER OPEN THE TELEVISION C aution CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE THE REAR COVER, NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. Mains voltage: 220V/230V/240V~, 50Hz. Control range of mains section: 100V-260V~ (option) or "indicated on the rear of the TV set". Mode CB CI CX CK CII CW CF CS CD System PAL-B/G PAL-I (UHF ONLY) PAL-B/G, SECAM-B/G PAL-B/G, D/K, SECAM-B/G, D/K PAL-I (WITH VHF BAND) PAL-B/G, D/K, SECAM-B/G, D/K, NTSC4. 43MHz PAL-B/G, SECAM-B/G, SECAM-L/L' PAL-B/G, D/K, SECAM-B/G, D/K, NTSC4. 43/3. 58MHz PAL-I, D/K Beware of high voltage. [. . . ] When you scan through the stored channels, those that you have chosen to skip are thus not displayed. All channels that you do not specifically choose to skip are displayed during scanning. Press the MENU. Result: The main on-screen menu is displayed. Use the and + to display the "Setup". 3 CH. skip P 0 : Added P 1 : Added P 2 : Added P 3 : Added Use the and + to display the "CH. Result: All the channels are listed in numerical order. 4 CH. skip P 0 : Added P 1 : Added P 2 : Erased P 3 : Added The list displays only four channels at a time. Next four channels Previous four channels To. . . Select the channel Erase a channel so that it will be skipped over during scanning Add a previously erased channel so that it will be displayed during scanning Press. . . , when the selection bar is on the last channel listed. , when the selection bar is on the first channel listed. Added. ­ + When you have finished, press the MENU repeatedly until the menus disappear. F ine-tuning Channel Reception 1 2 Setup Manual store Auto store CH. skip Fine tune Sort If reception is clear, you do not have to fine-tune the channel, as this is done automatically during the search and store operation. If however the signal is weak or distorted, you may have to finetune the channel manually. channel cannot be P4 UHF Press the MENU. Result: The main on-screen menu is displayed. Use the and + to display the "Setup" and then select the "Fine tune". Result: The channel number and frequency band are displayed above a horizontal cursor. Use the + and ­ to move the fine-tuning cursor until you obtain a sharp, clear picture and good sound quality. If you do not press either button within two seconds, the fine-tuning cursor disappears and the "Setup" is redisplayed. If this happens, reselect the "Fine tune". When you have finished, press the MENU repeatedly until the menus disappear. 9 A djusting the Picture 1 2 Menu Picture Setup Function Select Enter Exit : : : MENU Picture Contrast Brightness Sharpness Colour Tint 90 50 50 50 50 Several settings are available on your television to enable you to control the quality of the picture: Contrast ( Brightness ( Sharpness ( Colour ( Tint ( option ) ) - for NTSC signal; ) ) ) Option Press the MENU. Result: The main on-screen menu is displayed with the "Picture". Press the + to display the "Picture". Press the or to select the required option. 3 Your settings are only memorised if you have selected the "Custom" picture standard (for details, refer to "Choosing the Picture Standard"). Otherwise they are lost when: You switch the television off using the On/Off button (POWER) on the front panel There is a power failure 91 To move the on-screen cursor. . . [. . . ] When both the front and rear connectors are connected to external equipment, the front AV has the priority. Decoder/Video game 17 P roblems and Solutions Before contacting the after-sales service, perform the following simple checks. If you cannot solve the problem using the instructions below, note the model and serial number of the television and contact your local dealer. Problem No sound or picture Checks/Explanation/Solution Check that the mains lead has been connected to a wall socket and the wall socket is switched on. Check that you have pressed the On/Off button (POWER) on the front panel. Check the picture contrast and brightness settings. [. . . ]