User manual SAMSUNG CW-25M064VR OPEN SOURCE GUIDE (VER.1.1)

[. . . ] REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. The main voltage is indicated on the rear of the TV set and the frequency is 50 or 60Hz. WARNING: TO PREVENT DAMAGE WHICH MAY RESULT IN FIRE OR SHOCK HAZARD. DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. 2 ENG Contents PREPARING YOUR TELEVISION Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Caution . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Control Panels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Select a letter or number Move on the next letter Move back the previous letter Press the. . . oe button. Channel Name P0 P1 P2 P3 : ----: ----: ----: ----- Channel 5 6 The characters available are: Letters of the alphabet (A. . . Z) Numbers (0. . . 9) Special characters (space, -) Name P0 P1 P2 P3 : --------: ----: ----: ----- You can have each channel newlynamed. When you have finished entering the name, press the EXIT ( ) button, or press the MENU ( ) button repeatedly to return to normal viewing. 17 Skipping Unwanted Channels ENG Channel Auto Store Manual Store Name Add/Erase Fine Tune Sort You can exclude the channels of your choice from the channel scan operation. When you scan through the stored channels, those you have chosen to skip are not displayed. All channels that you do not specifically choose to skip are displayed during scanning. 1 Channel Add/Erase Press the MENU button. Press the or button to select the Channel and press the oe or button. Press the or button to select the Add/Erase and press the oe or button. Result: The Add/Erase menu is displayed. 2 3 P0 P1 P2 P3 : Added : Added : Added : Added 4 Channel Add/Erase P0 P1 P2 P3 : Erased : Added : Added : Added Press the or button to select the required channel. To add or erase the desired channel by pressing the oe or button. When you have finished adding and erasing channels, press the EXIT ( ) button or, press the MENU ( ) button repeatedly to return to normal viewing 5 6 18 Fine tuning Channel Reception ENG If the reception is clear, you do not have to fine-tune the channel, as this is done automatically during the search and store operation. If however the signal is weak or distorted, you may have to finetune the channel manually. Channel Auto Store Manual Store Name Add/Erase Fine Tune Sort 1 2 3 Press the MENU button. When you have been finished, press the EXIT ( ) button or, press the MENU ( ) button repeatedly to return to normal viewing. You can select the required picture effect by simply pressing the "P. MODE" (Picture Mode) button on the remote control. 21 Adjusting the Picture Settings ENG Your television has several settings which allow you to control picture quality: Picture oe Mode Custom Adjust Digital NR : Off Tilt :0 Color Tone, Contrast, Brightness, Sharpness, Color, Tint (NTSC only) 1 Press the MENU button. Result: The Picture menu is displayed. 2 Picture Adjust Press the oe or button. Press the or button to select the Adjust, and then press the oe or button. Result: When select the Mode to Custom, the Adjust menu is displayed. Result: You select the required option (Normal, Warm1/2, Cool1/2). Result: The horizontal bar is displayed. 3 Color Tone : Normal Contrast 90 Brightness 50 Sharpness 50 Color 50 4 To adjust the. . . Color Tone Picture Adjust Color Tone : Normal Contrast 90 Brightness 50 Sharpness 50 Color 50 Contrast Brightness Sharpness Color Tint (NTSC only) 5 91 The Sharpness and Tint are not available in DVD mode. Contrast When you are satisfied with the settings, press the EXIT ( ) button or, press the MENU ( ) button repeatedly to return to normal viewing. The television has an "automatic degaussing" system that is activated if magnetic interference is present. To degauss the television screen, switch power off by pressing the " " (ON/OFF) button on the front panel (refer to "Automatic Degaussing to Remove Color Patches" on page 36). If you make any changes to the Adjust settings, the picture standard is automatically switched to Custom. 22 Setting the Digital Noise Reduction ENG If the signal received by your television is weak, you can activate the Digital Noise Reduction feature to help reduce any static and ghosting that may appear on the screen. Picture oe Mode Custom Adjust Digital NR : Off Tilt :0 1 Press the MENU button. Result: The Picture menu is displayed. 2 3 4 Press the oe or button. Press the or button to select the Digital NR. [. . . ] Repeat steps 2 and 3 for each page to be stored, using a different colored button each time. Press the (store) button until the corresponding blocks are displayed in white. The button is used to switch between: LIST mode FLOF mode 36 Automatic Degaussing to Remove Color Patches ENG A degaussing coil is mounted around the picture tube, so you do not normally need to degauss the television manually. If you move the television to a different position and color patches appear on the screen, you must: Switch the television off by pressing the " Unplug the television from the wall socket Leave the television power-off (stand-by) for about 30 minutes so that the automatic degauss function can be activated, and then press the POWER ( ) button on the remote control. If your televisiontelevision will be left unattended, press the " off. [. . . ]