User manual SAMSUNG DSB-9401V

[. . . ] Use a cloth lightly dampened with water(no solvents) to clean the exterior. Ensure that free airflow is maintained around the STB. Never store the STB where it is exposed to direct sunlight or near heating equipment e. g. Never stack other electronic equipment on top of the STB. [. . . ] Press the OK key and then the Teletext VBI you want is displayed on the screen. 11. Audio Mode You can choose a mode among left, right or stereo using the BLUE(AUDIO) key. To change the audio mode: Press the BLUE(AUDIO) key to select the left, right or stereo. Press the EXIT key to save and escape from this menu. GB-14 D I G I T A L S A T E L L I T E R E C E I V E R GB-15 DSB-9401VF DSB-9401VF OPERATING THE RECEIVER OPERATING THE RECEIVER Main Menu After installing your antenna system and STB with appropriate connectors. 1. 1 LNB Setting You can select the satellite and LNB setting conditions to execute channel search and you can alter the settings for 22KHz tone. The parameters set in this menu are needed for programming the channels for the "Auto scanning" and "Manual scanning". The necessary information can be found at your antenna and LNB brochures, or you can ask your dealer. Select the DiSEqC Mode (Off, DiSEqC A, DiSEqC B, DiSEqC C, DiSEqC D, Tone Burst A, Tone Burst B) Plug in the AC main power and switch on the receiver. Press MENU key to bring up the main menu. The LED display will show "MENU". The following on screen display will appear: The sub menu topics will be displayed. For the sub-menus Installation, Channel Organising and Parental Lock you need the PIN Code. Before you begin with the "Installation" menu, you should check in the 4th menu "System Setup" whether all the information there is applicable for you. GB If you are using a Positioner, select Positioner DiSEqC1. 2 ("Yes" or "No") 22KHz: In case you are using a dual LNB or two antennas connected to a 22KHz tone switch box, with the 22 KHz tone switch ("On", "Off" or "Auto") you can switch between both LNB or antennas. To see the help message, press the YELLOW(ALT) key. 1. Select "Disable Limit", in order to disable "Set Limit". Select "Reset Positioner" and OK key to reset positioner. Press OK key. Auto Scanning menu will be displayed. All the channels in the list from the selected satellite will be automatically downloaded. After scanning you will see "Your digital receiver found. . . ". Then, you should press OK key to store all channels into STB. GB-18 D I G I T A L S A T E L L I T E R E C E I V E R GB-19 DSB-9401VF 1. 5 Manual Scanning DSB-9401VF OPERATING THE RECEIVER OPERATING THE RECEIVER 1. 6 SMATV Scanning In case that several generations use Antenna and LNB in common, search the service the from 950 to 2150MHz. Select Searching Type "Automatic" or "Manual". Select Scan Mode "All" or "Only Free". You can input alternative symbol rate from 1st to 4th. To tune-in new channels and weak signals, the STB has been provided with the option "Manual Scanning" where the channel data can be entered by the user. After selecting the "Manual Scanning" from the Installation Menu, the following screen will be displayed: Select the target satellite for manual search. In order to scan programs from the satellite which is not listed on this menu, select `Satellite 1', `Satellite 2' or `Satellite 3'. In case of `Satellite 1', `Satellite 2' or `Satellite 3', all information about the satellite which you are interested in should be put. [. . . ] Slave Box(Installing Box) : Menu Mode 4. Connect 2 Boxes with RS232 serial cable (Both end should have male connector with crossed signals) 5. Select the `System Setup' and press the OK key. Select the `Copy Channel Data' with the / keys. [. . . ]